Publications related to Printing on liquid elastomers

A multi-material robotic finger with integrated proprioceptive and tactile capabilities produced with a circular process

Antonia Georgopoulou Papadonikolaki, Josephine Anna Eleanor Hughes, Kai Christian Junge

When developing or designing biomimetic robotic fingers with rigid and soft components and integrated sensors, fabrication is often a bottle-neck when assembling and casting processing techniques are used. This study introduces a thermoplastic multi-materi ...

IEEE2023

Biocompatible and Biodegradable 3D Printing from Bioplastics: A Review

Sandro Carrara

There has been a lot of interest in developing and producing biodegradable polymers to address the current environmental problem caused by the continued usage of synthetic polymers derived from petroleum products. Bioplastics have been identified as a poss ...

MDPI2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023

Additive and digital manufacturing of transient sensors and bioelectronics

Nicolas Francis Fumeaux

Transient electronics have emerged as a promising class of devices, capable of breaking down without harmful side effects to their environment. They have tremendous potential as bioresorbable electronics for temporary applications in the human body, and as ...

EPFL2023

Selective Growth of van der Waals Heterostructures Enabled by Electron-Beam Irradiation

Aleksandra Radenovic, Michal Daniel Macha

Van der Waals heterostructures (vdWHSs) enable the fabricationof complex electronic devices based on two-dimensional (2D) materials.Ideally, these vdWHSs should be fabricated in a scalable and repeatableway and only in the specific areas of the substrate t ...

AMER CHEMICAL SOC2023

Digital manufacturing of personalised footwear with embedded sensors

Danick Briand, Rubaiyet Iftekharul Haque, Ryan Mitchell van Dommelen, Jaemin Kim

The strong clinical demand for more accurate and personalized health monitoring technologies has called for the development of additively manufactured wearable devices. While the materials palette for additive manufacturing continues to expand, the integra ...

Nature Research2023

Volumetric additive manufacturing in a scattering resin

Jorge Andres Madrid Wolff

Volumetric 3D printing is a novel technique that offers promising new perspectives in tissue engineering. In volumetric 3D printing, photosensitive gels or liquids are solidified by projecting light patterns via reverse tomography. Recent results show that ...

EPFL2023

Reinforced Supramolecular Networks of End Functionalized Polymers for Tailored Thermomechanical Property Profiles

Yevhen Hryshunin

Thermoset rubbers give rise to elastomers with tunable stiffness and high resilience but are not recyclable. Thermoplastic elastomers can address this problem but their broad applicability is impeded by either limited operating temperatures or inferior ela ...

EPFL2023

Modeling the mechanics and rheology of porous and granular media: an elastoplastic continuum approach

Lars Kristoffer Uhlen Blatny

The complex mechanics of porous and granular media play a significant role in various industrial processes and natural phenomena. As an example, understanding the mechanics of how failure occurs, localizes and propagates in porous brittle solids under vari ...

EPFL2023

A hybrid Selective Laser Sintering based process for the additive manufacturing of architectured composites

Erwan Philippe Guenier

Additive Manufacturing also commonly referred as 3D printing has been given a lot of interest lately. Market is growing exponentially and the aim for obtaining more complex and ready-to use parts is emerging. All the 3D printing processes consist in buildi ...

EPFL2023

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Solvent-Free Synthesis and Processing of Conductive Elastomer Composites for Green Dielectric Elastomer Transducers

Frank Nüesch

Stretchable electrodes are more suitable for dielectric elastomer transducers (DET) the closer the mechanical characteristics of the electrodes and elastomer are. Here, a solvent-free synthesis and processing of conductive composites with excellent electri ...

WILEY-V C H VERLAG GMBH2022

Highly Stretchable Silicone Elastomer Applied in Soft Actuators

Fabio Beco Albuquerque, Pengpeng Hu

In this work, a highly stretchable silicone elastomer is incorporated into dielectric elastomer actuators (DEAs) in order to decrease operation voltages by applying high prestretches. Results show that the fabricated DEAs (5 mm diameter circle active regio ...

WILEY-V C H VERLAG GMBH2022

Dielectric properties of 3-3 flexible composites by infiltration of elastomers into porous ceramic structures using cellulose scaffold

Frank Nüesch, Thomas Geiger

Elastomer composites are prepared by infiltrating polydimethylsiloxane (PDMS) into a porous ceramic structure of nanoparticles. This method differs from the conventional approach, where particles are dispersed into the polymer matrix, since here, the polym ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Slot-Die Coating of an On-the-Shelf Polymer with Increased Dielectric Permittivity for Stack Actuators

Yauhen Sheima

Nitrile-butadiene rubbers (NBR) have been extensively used as dielectric materials due to their commercial availability, excellent mechanical properties, glass transition temperature below 0 degrees C, and increased dielectric permittivity owing to the pre ...

AMER CHEMICAL SOC2022

3D printing of elastomeric mechanical sensors designed for human motion monitoring

Ryan Mitchell van Dommelen

In this thesis several advances are made to the emerging field of 3D printed mechanical sensors. Techniques and processes were developed to enable the integration of highly conductive, and capacitive and piezoresistive sensing features embedded within 3D p ...

EPFL2022

Weakening effect of various pore fluids on the tensile strength of granite

Guanyi Lu

Laboratory three-point bending experiments are carried out to evaluate the effect of various fluids on the tensile strength of granite. The granite specimens were tested under both dry and saturated conditions. The fluids used to saturate the granite inclu ...

SPRINGER HEIDELBERG2022

Automated test setup to quantify the lifetime of dielectric elastomer actuators under a wide range of operating conditions

Herbert Shea, Fabio Beco Albuquerque, Valentin Colin Py, Djen Timo Kühnel

We present an automated test setup for the systematic performance and lifetime evaluation of dielectric elastomer actuators (DEAs). This setup, called the MAPLE setup, performs accelerated aging tests and allows quantifying how material choice, fabrication ...

IOP PUBLISHING LTD2021