Lecture

Embedded Systems: Control Basics

Graph Chat

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

In course

ENG-366: Signals, instruments and systems

The goal of this course is to transmit knowledge in sensing, computing, communicating, and actuating for programmable field instruments and, more generally, embedded systems. The student will be able to put in practice the knowledge acquired using concrete ...

Description

This lecture covers the fundamentals of control systems in embedded systems, including open- and closed-loop control, real-time programming, interrupts, and sensor networks. The instructor explains the importance of controllers, the perception-to-action loop, and the challenges of programming embedded systems. Real-time systems and the use of interrupts for accurate timing are discussed. The lecture also delves into sensor networks, emphasizing the Sensorscope project and the implementation of multi-hop networks. Time synchronization in sensor networks and practical examples from the field are presented, highlighting the significance of resource management and real-time constraints in embedded systems.

Instructor

Alcherio Martinoli

I received my Diploma in Electrical Engineering from the Swiss Federal Institute of Technology in Zurich (ETHZ), and a Ph.D. in Computer Science from the Swiss Federal Institute of Technology in Lausanne (EPFL). I am currently an Associate Professor at the School of Architecture, Civil, and Environmental Engineering and the head of the Distributed Intelligent Systems and Algorithms Laboratory. Before joining EPFL I carried out research activities at the Institute of Biomedical Engineering of the ETHZ, at the Institute of Industrial Automation of the Spanish Research Council in Madrid, Spain, and at the California Institute of Technology, Pasadena, U.S.A. Additional information can be found on my full CV.

Official source

Ontological neighbourhood

Computer engineering

High-performance computing: Real-time computing

Related concepts (32)

Interrupt

In digital computers, an interrupt (sometimes referred to as a trap) is a request for the processor to interrupt currently executing code (when permitted), so that the event can be processed in a timely manner. If the request is accepted, the processor will suspend its current activities, save its state, and execute a function called an interrupt handler (or an interrupt service routine, ISR) to deal with the event.

Interrupt handler

In computer systems programming, an interrupt handler, also known as an interrupt service routine or ISR, is a special block of code associated with a specific interrupt condition. Interrupt handlers are initiated by hardware interrupts, software interrupt instructions, or software exceptions, and are used for implementing device drivers or transitions between protected modes of operation, such as system calls. The traditional form of interrupt handler is the hardware interrupt handler.

Non-maskable interrupt

In computing, a non-maskable interrupt (NMI) is a hardware interrupt that standard interrupt-masking techniques in the system cannot ignore. It typically occurs to signal attention for non-recoverable hardware errors. Some NMIs may be masked, but only by using proprietary methods specific to the particular NMI. An NMI is often used when response time is critical or when an interrupt should never be disabled during normal system operation.

Interrupt request

In a computer, an interrupt request (or IRQ) is a hardware signal sent to the processor that temporarily stops a running program and allows a special program, an interrupt handler, to run instead. Hardware interrupts are used to handle events such as receiving data from a modem or network card, key presses, or mouse movements. Interrupt lines are often identified by an index with the format of IRQ followed by a number. For example, on the Intel 8259 family of programmable interrupt controllers (PICs) there are eight interrupt inputs commonly referred to as IRQ0 through IRQ7.

Real-time computing

Real-time computing (RTC) is the computer science term for hardware and software systems subject to a "real-time constraint", for example from event to system response. Real-time programs must guarantee response within specified time constraints, often referred to as "deadlines". Real-time responses are often understood to be in the order of milliseconds, and sometimes microseconds. A system not specified as operating in real time cannot usually guarantee a response within any timeframe, although typical or expected response times may be given.

Related lectures (64)

Process Protection and Efficient Execution

Explores process execution, protection, and efficient OS mechanisms for secure and reliable multi-program environments.

IO Devices: Interaction and Performance

Covers the interaction between operating systems and IO devices, focusing on hardware fundamentals and performance implications.

Timers and Counters: Architecture and Applications

Explores the architecture and applications of timers and counters in microcontrollers for generating precise time bases and signals.

Traps and Interrupts: Mechanisms for Operating System Control

Explains traps, interrupts, and exceptions, detailing their roles in operating system control and process management.

Isolation and Protection: Ensuring Process Security