Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Heat illness

Related publications (11)

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

Roland Logé

The microstructure evolution associated with the cold forming sequence of an Fe-14Cr-1W-0.3Ti-0.3Y2O3 grade ferritic stainless steel strengthened by dispersion of nano oxides (ODS) was investigated. The material, initially hot extruded at 1100 degrees C an ...

MDPI2024

Development of High-Strength Aluminum Alloys for Additive Manufacturing

Marvin Lennard Schuster

Metal additive manufacturing (AM) offers the possibility to rapidly produce complex geometries that are not achievable with conventional manufacturing methods. The two most common technologies, Laser Powder Bed Fusion (LPBF) and Direct Metal Deposition (DM ...

EPFL2022

Effect of post-heat treatment conditions on shape memory property in 4D printed Fe-17Mn-5Si-10Cr-4Ni shape memory alloy

Christian Leinenbach, Irene Ferretto

The influence of post-heat treatment on the microstructure and properties of 4D printed Fe-17Mn-5Si-10Cr-4Ni (wt. %) shape memory alloy (SMA) produced via a laser powder bed fusion process is investigated in this study. It is shown that heat-treatment temp ...

2022

Mechanistic Study on Thermally Induced Lattice Stiffening of ZIF-8

Kumar Varoon Agrawal, Wendy Lee Queen, Pascal Alexander Schouwink, Mehrdad Asgari, Qi Liu, Deepu Joseph Babu, Jian Hao

The flexibility of the ZIF-8 aperture, which inhibits a molecular cutoff of 3.4 angstrom, can be reduced by rapid heat treatment to obtain CO2-selective membranes. However, the early stages of the structural, morphological, and chemical changes responsible ...

2021

Influence of interfacial structural disorder and/or chemical interdiffusion on thermal boundary conductance for Ti/Si and Au/Si couples

Ludger Weber, Maïté Blank

This work aims at experimentally assessing the effect of structural disorder and/or chemical interdiffusion on thermal boundary conductance (TBC) at metal/dielectric interfaces. To this end, the TBC of Au/Si and Ti/Si interfaces was measured by time domain ...

2019

Combined Rehabilitation Promotes the Recovery of Structural and Functional Features of Healthy Neuronal Networks after Stroke

Silvestro Micera

Rehabilitation is considered the most effective treatment for promoting the recovery of motor deficits after stroke. One of the most challenging experimental goals is to unambiguously link brain rewiring to motor improvement prompted by rehabilitative ther ...

2019

Effect of μM Fe addition, mild heat and solar UV on sulfate radical-mediated inactivation of bacteria, viruses, and micropollutant degradation in water

César Pulgarin, Luiz Felippe De Alencastro, Stefanos Giannakis, Dominique Grandjean

In this work, solar disinfection (SODIS) was enhanced by moderate addition of Fe and sodium perox- ydisulfate (PDS), under solar light. A systematic assessment of the activating factors was performed, firstly isolated, then in pairs and concluded in the co ...

2018

Synthesis and characterization of fluorinated anatase nanoparticles and subsequent N-doping for efficient visible light activated photocatalysis

Paul Bowen, Sami Rtimi, Irena Markovic

Fluorinated-titanium dioxide (TiO2-F) nanoparticles in a pure anatase polymorph was precipitated from solution by hydrolysis of titanium oxychloride, using urea and ammonia as precipitation agents and potassium fluoride as a source of fluorine anion. A fur ...

2018

Numerical Simulation of Solidification, Homogenization, and Precipitation in an Industrial Ni-Based Superalloy

Alain Jacot, Charles-André Gandin, Luc Rougier

A comprehensive simulation approach integrating solidification, homogenization, and precipitation during aging has been used to predict the formation of gamma/gamma' microstructures in the AM1 nickel-based superalloy. The particle size distribution of intr ...

Springer2016

Simulation de la formation des microstructures dans les superalliages à base de nickel de type AM1 durant la solidification et les traitements thermiques

Luc Rougier

Nickel base superalloys are used for the manufacturing of monocrystalline turbine blades, due to their outstanding mechanical properties at high temperature. The mechanical properties strongly depend on the presence of γ’ precipitates in the γ matrix. Impr ...

EPFL2013

Rational Design of Pd-Based Catalysts for Selective Alkyne Hydrogenations

Rocio Micaela Crespo Quesada

Traditionally, the search for active and selective catalysts involved a rather tedious "hit-and-miss" approach in which hundreds, if not thousands catalysts were tested until the optimal substance was identified. With the advancing theoretical understandin ...

EPFL2011