Publications associées à Long-term compression performance of a pultruded GFRP element exposed to concrete pore water solution

Publications associées (35)

Methodology for Calibrating Fatigue Load Models for Composite Road Bridges

Current fatigue load models (FLMs) for road bridges are typically calibrated based on steel and reinforced-concrete bridges. These models are not likely applicable to fiber–polymer composite bridges, primarily because the damage rate—defined as the slope o ...

2025

Optimizing photon capture: advancements in amorphous silicon-based microchannel plates

Edoardo Charbon, Christophe Ballif, Claudio Bruschini, Nicolas Würsch, Luca Massimiliano Antognini, Emanuele Ripiccini, Jad Benserhir, Samira Alexandra Frey

Microchannel plates are electron multipliers widely used in applications such as particle detection, imaging, or mass spectrometry and are often paired with a photocathode to enable photon detection. Conventional microchannel plates, made of glass fibers, ...

2025

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Innovative thermophysical characterization of an ATF composite cladding: the case of silicon carbide

Andrea Cavaliere

Nuclear power is a powerful technology that plays an important role in the fight against climate change, and research is continuously engaged in studies that could further improve its safety. After the Fukushima accident, Accident Tolerant Fuels research h ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

2024

Influence of fiber orientation on the high cycle tensile fatigue resistance of Ultra-High Performance Fiber Reinforced Cementitious

Eugen Brühwiler, Alain Nussbaumer, Jian Zhan

This paper quantitatively studies the influence of fiber orientation on the high cycle tensile fatigue resistance of ultra-high performance fiber reinforced cementitious composites (UHPFRC) within and beyond elastic domain. Eight tensile fatigue tests and ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Micro modeling of irregular stone masonry walls using mathematical programming

Katrin Beyer, Qianqing Wang, Ketson Roberto Maximiano Dos Santos

While understanding the shear strength of stone masonry structures is important for the design and the mainte- nance, we still lack computational tools for predicting the strength as a function of the stone layout. Here we implement an end-to-end image bas ...

Springer2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Corentin Jean Dominique Fivet, Célia Marine Küpfer

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024