Long-term compression performance of a pultruded GFRP element exposed to concrete pore water solution

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

Current fatigue load models (FLMs) for road bridges are typically calibrated based on steel and reinforced-concrete bridges. These models are not likely applicable to fiber–polymer composite bridges, primarily because the damage rate—defined as the slope o ...

Microchannel plates are electron multipliers widely used in applications such as particle detection, imaging, or mass spectrometry and are often paired with a photocathode to enable photon detection. Conventional microchannel plates, made of glass fibers, ...

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

Nuclear power is a powerful technology that plays an important role in the fight against climate change, and research is continuously engaged in studies that could further improve its safety. After the Fukushima accident, Accident Tolerant Fuels research h ...

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

This paper quantitatively studies the influence of fiber orientation on the high cycle tensile fatigue resistance of ultra-high performance fiber reinforced cementitious composites (UHPFRC) within and beyond elastic domain. Eight tensile fatigue tests and ...

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

While understanding the shear strength of stone masonry structures is important for the design and the mainte- nance, we still lack computational tools for predicting the strength as a function of the stone layout. Here we implement an end-to-end image bas ...

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

Long-term compression performance of a pultruded GFRP element exposed to concrete pore water solution

Chat with Graph Search

Methodology for Calibrating Fatigue Load Models for Composite Road Bridges

Optimizing photon capture: advancements in amorphous silicon-based microchannel plates

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Experimental investigation of dowel action in reinforcing bars using refined measurements

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Innovative thermophysical characterization of an ATF composite cladding: the case of silicon carbide

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Influence of fiber orientation on the high cycle tensile fatigue resistance of Ultra-High Performance Fiber Reinforced Cementitious

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Micro modeling of irregular stone masonry walls using mathematical programming

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

FLO:RE – A new floor system made of reused reinforced concrete and steel elements