Publications associées à New framework for calibration of partial safety factors for fatigue design

Publications associées (35)

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Improved Material Formulations for Thick Adhesive Joints in Wind Turbine Blades

Jialiang Fan

Wind turbine rotor blades are usually fabricated using composite materials and epoxy adhesive to bond the elements together. Due to their large size, the thickness of the adhesive layer varies from 1 to up to 30 mm depending on the position. The failure of ...

EPFL2024

Strain-based analysis on the influence of local undercut geometry on fatigue crack initiation life

Alain Nussbaumer

The local undercut defects at the weld toe provide a potential initiation site for fatigue cracks and significantly impact the structure's fatigue strength. The influence of continuous undercut depth on fatigue performance is widely studied, but the resear ...

2024

Experimental and numerical evaluation of a U-shaped thin lightly reinforced concrete wall tested under cyclic loading

Katrin Beyer

Reinforced concrete walls provide effective bracing against seismic lateral loading for buildings worldwide. In Latin America, seismic design provisions commonly adhere to the ACI 318 building code, which is predominantly based on United States constructio ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Effects of physiotherapy and home-based training in parkinsonian syndromes: protocol for a randomised controlled trial (MobilityAPP)

Kamiar Aminian, Anisoara Ionescu

All rights reserved.Introduction Gait and mobility impairment are pivotal signs of parkinsonism, and they are particularly severe in atypical parkinsonian disorders including multiple system atrophy (MSA) and progressive supranuclear palsy (PSP). A pilot s ...

2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Fatigue of reinforced UHPFRC members and monitoring of fatigue action effects on bridges

Bartlomiej Wojciech Sawicki

The objective of this thesis is to develop knowledge and methods to prevent fatigue failure of bridges. The Fatigue Limit State is investigated from both the demand (S) and resistance (R) side. The S-part focuses on reduction of uncertainties through monit ...

EPFL2021

Multiaxial fatigue behavior and strengthening of riveted double-angle connections in steel bridges using prestressed CFRP rods

Hossein Heydarinouri

A large number of aging road and railway riveted metallic bridges suffer from fatigue problems. Stringer-to-floor-beam double-angle bridge connections are among the most fatigue-prone details due to the many cyclic distortion-induced stresses from axle loa ...

EPFL2021

Multiaxial fatigue analysis of high-strength steel welded joints using generalized local approaches

Martin Antonio René Garcia

The objective of this thesis is to improve methods for predicting the fatigue life, multiaxial or not, of mild- and more particularly high-strength steels using local approaches that have the capacity to be applicable to almost any cases, hence the term ge ...

EPFL2020

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

Static and Fatigue Biaxial Flexural Behavior of Strain-Hardening UHPFRC Thin Slab Elements

Xiujiang Shen

Cast-in-place thin layers of Ultra-High Performance Fiber Reinforced Cementitious Composites (UHPFRC) on the specific zones of existing reinforced concrete (RC) bridge decks has been demonstrated to be a technically efficient and economic rehabilitation an ...

EPFL2020

Uniaxial Cyclic and Tensile Tests on Structural Metallic Materials

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Selimcan Ozden

Experimental data is imperative to characterize the behavior of materials used in structural analysis models. The aim of this data paper is to establish a database of material-scale uniaxial experiments, primarily conducted at EPFL, to assist with simulati ...

ASCE-AMER SOC CIVIL ENGINEERS2023

3D laser shock peening - A new method for improving fatigue properties of selective laser melted parts

Roland Logé, Christian Leinenbach, Nikola Kalentics, Manuel Ortega Varela De Seijas

Although Selective Laser Melting (SLM) currently revolutionizes the way parts are being manufactured, certain process inherent limitations such as accumulation of residual stresses and increased porosity content can lead to a decrease in fatigue life of pr ...

ELSEVIER2020

Stress ratio effect on tension-tension fatigue behavior of angle-ply GFRP laminates

Thomas Keller, Anastasios Vassilopoulos

The effect of the stress ratio (R = sigma(min)/sigma(max)) on the fatigue behavior of (+/- 45)(2s) angle-ply glass/epoxy composite laminates was investigated by comparing their mechanical, thermal, and optical properties under the stress ratio of 0.5 with ...

2019

Multiaxial ultra low cycle fatigue in welded high strength steel structural components

Alain Nussbaumer, Albano António De Abreu E Presa De Castro E Sousa

Extreme events often subject regions of structural steel components to large inelastic strains. In conditions such as earthquakes, exceptional winds gusts or tides the loading scenario is cyclical, variable amplitude and frequently multiaxial in nature, an ...

2019

Load history effects in fibre-reinforced polymer composite materials

Abdolvahid Movahedirad

Today, it is widely accepted that fatigue is one of the most common failure mechanisms in structural components, and pure static failure is rarely observed. Engineering structures are subjected to complex mechanical fatigue loading histories, which cause d ...

EPFL2019

Two-dimensional crack growth in FRP laminates and sandwich panels

Aida Cameselle Molares

Fiber-reinforced polymer (FRP) composite materials are currently being selected for the design of lightweight and efficient structural members in a wide number of engineering applications. Sandwich panels with glass fiber-reinforced polymer (GFRP) face she ...

EPFL2019

Re:Crete - A Footbridge made of Reused Concrete Blocks

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Jan Friedrich Georg Brütting, Célia Marine Küpfer, Julie Rachel Devènes

Today, concrete is the most widely used construction material worldwide. Strong, versatile, durable, and vector of economic development, this exceptional material is also the principal cause of greenhouse-gas emissions, material depletion and waste generat ...

Asociación Española de Ingeniería Estructura2022

Fatigue safety verification of a steel railway bridge using short term monitoring data

Eugen Brühwiler, Bartlomiej Wojciech Sawicki

The case study of the fatigue safety examination of the 120 years old steel riveted bridge carrying a single railway track on two main girders is presented. The overall assessment according to the Swiss Standard SIA 269 for existing structures indicated su ...

CRC PRESS-TAYLOR & FRANCIS GROUP2019