Publications associées à Extension of GeN-Foam to modeling of boiling water and validation against the OECD/NRC PSBT benchmark

Publications associées (32)

Extension of GeN-Foam to departure from nucleate boiling prediction and validation against the OECD/NRC PSBT benchmark

The prediction of departure from nucleate boiling (DNB) has always been a crucial aspect of thermal-hydraulic codes for the analysis of Light Water Reactors. In this paper, GeN-Foam, a multi-physics code developed based on OpenFOAM, has been enhanced to in ...

Elsevier Science Sa2023

Heat transfer of uncoated and nanostructure coated commercially micro-enhanced refrigeration tubes under pool boiling conditions

John Richard Thome

The heat transfer performance of commercially produced micro-enhanced tubes with and without a nanocoating was investigated under pool boiling of saturated refrigerant. These multiscale enhancements were on the outside of 19 mm horizontal copper tubes heat ...

Pergamon-Elsevier Science Ltd2023

From coating flow patterns to porous body wake dynamics via multiscale models

Pier Giuseppe Ledda

Multiscale phenomena are involved in countless problems in fluid mechanics. Coating flows are known to exhibit a broad variety of patterns, such as wine tears in a glass and dripping of fresh paint applied on a wall. Coating flows are typically modeled und ...

EPFL2022

Flow Boiling of Carbon Dioxide at Different Channel Orientations for the Thermal Management of Future Detector Technologies at the High-Luminosity Large Hadron Collider at CERN

David Schmid

The global warming potential (GWP) of working fluids in thermodynamic cycles and their environmental impact have been gaining considerable attention within the recent years. The global objectives on climate protection are becoming increasingly ambitious, w ...

EPFL2022

A parametric study on pool boiling heat transfer and critical heat flux on structured surfaces with artificial cavities

Luis Guillermo Villanueva Torrijo

Emerging applications in new generation electronic devices require effective heat removal and thermal man-agement. In this regard, boiling is a phase change phenomenon capable of dissipating a large amount of heat compared to the sensible heat. In this stu ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Fundamental study on microlayer dynamics in nucleate boiling

Lubomír Bures

Dynamics of nucleate boiling are strongly affected by the formation and behaviour of the microlayer, a layer of liquid underneath growing bubbles. As a result of its minute thickness, very high heat fluxes occur within the microlayer and its evaporation co ...

EPFL2021

Simulation and experimental validation of pulsating heat pipes

John Richard Thome, Jackson Braz Marcinichen, Philippe Aubin, Filippo Cataldo

The one-dimensional transient numerical code of JJ Cooling Innovation has been significantly improved to simulate the thermal/hydraulic performance of pulsating heat pipes (PHPs). Using a mechanistic approach, the liquid slug and vapor plug flows and their ...

PERGAMON-ELSEVIER SCIENCE LTD2021

Multiphase transport and evaporative cooling in fuel cell gas diffusion layers

Sarah van Rooij

The use of evaporative cooling in the gas diffusion layer (GDL) of polymer electrolyte fuel cells has been proposed as a simple yet impactful solution to simultaneously provide the functionality of cell cooling, thanks to the dissipation of the latent heat ...

EPFL2021

Gravity-Independent Oscillate Boiling

Mohamed Farhat, Outi Supponen

Heat transfer in nucleate boiling relies on the detachment and rise of the boiling bubble, in which gravity plays the dominant role. Previous studies showed that in the absence of gravity, the bubble fails to rise, causing the dryout of the heater and sign ...

SPRINGER2019

Fundamental Issues, Technology Development, and Challenges of Boiling Heat Transfer, Critical Heat Flux, and Two-Phase Flow Phenomena with Nanofluids

John Richard Thome

This paper presents a comprehensive and critical review of studies on nucleate pool boiling heat transfer, flow boiling heat transfer, critical heat flux (CHF), and two-phase flow phenomena with nanofluids. First, general analysis of the available studies ...

TAYLOR & FRANCIS INC2019

Numerical Simulations of Pulsating Heat Pipes, Part 1: Modeling

Brian Paul D'Entremont, John Richard Thome, Jackson Braz Marcinichen, Raffaele Luca Amalfi, Philippe Aubin, Filippo Cataldo

The pulsating nature of a closed loop pulsating heat pipe (CLPHP) makes the prediction of its thermal-hydraulic performance extremely challenging. Unfortunately, the design of CLPHPs is still quite an empirical process, requiring testing of many prototypes ...

IEEE2019

Optimum ratio of hydrophobic to hydrophilic areas of biphilic surfaces in thermal fluid systems involving boiling

Luis Guillermo Villanueva Torrijo, Tom Larsen

Pool boiling has a high heat removal capability and is considered as one of the most effective cooling methods due to utilization of latent heat of vaporization. Surface wettability plays a key role in boiling heat transfer since it controls the contact li ...

2019

Flow Boiling Heat Transfer and Pressure Drops of R1234ze(E) in a Silicon Micro-pin Fin Evaporator

John Richard Thome, Mirco Magnini, Chiara Falsetti

The development of newer and more efficient cooling techniques to sustain the increasing power density of high-performance computing systems is becoming one of the major challenges in the development of microelectronics. In this framework, two-phase coolin ...

Asme2017

From Nano- to Micrometer Scale: The Role of Antisolvent Treatment on High Performance Perovskite Solar Cells

Mohammad Khaja Nazeeruddin, Yi Zhang, Francesco Stellacci, Peng Gao, Sanghyun Paek, Giulia Grancini, Kyung Taek Cho, Pascal Alexander Schouwink, Evangelia-Nefeli Athanasopoulou

To date, antisolvent treatment has become one of the most important means to fabricate high efficiency perovskite solar cells (PSCs); however, the few reported antisolvents have not been analyzed on a uniform platform, and there is hitherto no clear reason ...

American Chemical Society2017

An updated three-zone heat transfer model for slug flow boiling in microchannels

John Richard Thome, Mirco Magnini

This work proposes a novel physics-based model for the fluid mechanics and heat transfer associated with slug flow boiling in horizontal circular microchannels to update the widely used three-zone model of Thome et al. (2004). The heat transfer model has a ...

Pergamon-Elsevier Science Ltd2017

Insulation effect on thermal stability of Coated Conductors wires in liquid nitrogen

Bertrand Dutoit, Bertrand Dutoit

Superconducting wires are not perfectly homogeneous in term of critical current as well as stabilization. In resistive fault current limiter applications this could lead to hot spots if the fault current is only slightly above the nominal current of the de ...

Iop Publishing Ltd2017

Influence of the Coriolis force on the structure and evolution of wind turbine wakes

Fernando Porté Agel, Mahdi Abkar

In this study, large-eddy simulation combined with a turbine model is used to investigate the effect of vertical wind veer associated with the Coriolis force on the structure and evolution of wind turbine wakes. In order to isolate the Coriolis effect on t ...

Amer Physical Soc2016

Two-Phase Heat Transfer Mechanisms within Plate Heat Exchangers : Experiments, Modeling and Simulations

Raffaele Luca Amalfi

Plate heat exchangers are adopted in many domestic and industrial applications, such as ventilation, air conditioning, evaporation or condensation process, heat pumps and cooling of hydrodynamic circuits in engines. In the present thesis, an extensive expe ...

EPFL2016

A CFD study of the parameters influencing heat transfer in microchannel slug flow boiling

John Richard Thome, Mirco Magnini

Boiling heat transfer in microchannels has been investigated extensively in the last two decades. However, most results from independent experimental studies display a substantial disagreement on the influence of the flow conditions and mechanisms on the h ...

Elsevier France-Editions Scientifiques Medicales Elsevier2016

Thermally-nucleated self-assembly of water and alcohol into stable structures at hydrophobic interfaces

Francesco Stellacci, Michele Ceriotti, Kislon Voitchovsky, Daniele Giofré

At the interface with solids, the mobility of liquid molecules tends to be reduced compared with bulk, often resulting in increased local order due to interactions with the surface of the solid. At room temperature, liquids such as water and methanol can f ...

Nature Publishing Group2016