Publications associées à Micromechanics of Amorphous Metal/Polymer Hybrid Structures with 3D Cellular Architectures: Size Effects, Buckling Behavior, and Energy Absorption Capability

Colloidal Atomic Layer Deposition on Nanocrystals Using Ligand-Modified Precursors

Raffaella Buonsanti, Anna Loiudice, Petru Pasquale Albertini, Ona Segura Lecina, Coline Marie Agathe Boulanger, Philippe Benjamin Green, Mark Adrian Newton, Krishna Kumar, Jari Leemans

Atomic layer deposition (ALD) is a method to grow thin metal oxide layers on a variety of materials for applications spanning from electronics to catalysis. Extending ALD to colloidally stable nanocrystals promises to combine the benefits of thin metal oxi ...

Amer Chemical Soc2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Font Side Solutions for c-Si Solar Cells with High-Temperature Passivating Contacts

Ezgi Genç

In this work, we studied the potential of using thin films deposited by plasma-enhanced chemical vapor deposition (PECVD) for two main purposes: introducing an n-type passivating contact at the front of a TOPCon solar cell, or simplifying the fabrication o ...

EPFL2024

Optimizing Atomic Layer Deposition Processes with Nanowire-Assisted TEM Analysis

Johann Michler, Ivo Utke, Xavier Maeder

Atomic layer deposition (ALD) is one of the premier methods to synthesize ultra-thin materials on complex surfaces. The technique allows for precise control of the thickness down to single atomic layers, while at the same time providing uniform coverage ev ...

Wiley2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Influence of ionization and cumulative effects on laser-induced crystallization in multilayer dielectrics

Yves Bellouard, Ruben Ricca, Victor Carle Adrien Boureau

Crystallization of amorphous layers has been demonstrated under various radically different laser-exposure conditions, including continuous wave (cw) and pulsed lasers. Here, we investigate the specific role of ionization in the crystallization of dielectr ...

2024

Nanostructure and Optical Property Tailoring of Zinc Tin Nitride Thin Films through Phenomenological Decoupling: A Pathway to Enhanced Control

Aïcha Hessler-Wyser, Johann Michler, Amit Sharma, Daniele Casari, Caroline Hain, Thomas Nelis

This work addresses the need for precise control of thin film sputtering processes to enable thin film material tailoring on the example of zinc tin nitride (ZTN) thin films deposited via microwave plasma-assisted high power reactive magnetron sputtering ( ...

Amer Chemical Soc2024

Computational Homogenization for Inverse Design of Surface-based Inflatables

Mark Pauly, Francis Julian Panetta, Uday Kusupati, Yingying Ren, Florin Isvoranu, Seiichi Eduardo Suzuki Erazo

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

2024

Piezoelectric and elastic properties of Al0.60Sc0.40N thin films deposited on patterned metal electrodes

Luis Guillermo Villanueva Torrijo, Silvan Stettler, Marco Liffredo, Nan Xu, Federico Peretti

Sc-doped aluminum nitride (AlScN) allows for piezoelectric devices with large electromechanical coupling and the benefits increase with larger Sc doping in the film. However, with a larger Sc concentration, the process window narrows, and it is necessary t ...

2024

Spinel Protective Coatings for Solid Oxide Cell (SOC) Interconnects (ICs)

Samaneh Daviran

Abstract The degradation of metal interconnects (ICs) in Solid Oxide Cells (SOCs) primarily results from chromium (Cr) oxide scale growth on stainless-steel substrates, causing ohmic loss and air-side electrode poisoning by Cr. This thesis addresses these ...

EPFL2024

Microstructural and electrical characterization of high temperature passivating contacts for silicon solar cells

Sofia Libraro

Recombination at metal/semiconductor interfaces represents the main limitation in mainstream c-Si solar cells, primarily based on the passivated emitter and rear cell (PERC) concept. Full-area passivating contacts based on SiOx/poly-Si stacks are a candida ...

EPFL2024

Towards Scalable Electronics: Synthetic 2D Materials for Large-Area 2D Circuit Integration

Zhenyu Wang

In the past decades, a significant increase of the transistor density on a chip has led to exponential growth in computational power driven by Moore's law. To overcome the bottleneck of traditional von-Neumann architecture in computational efficiency, effo ...

EPFL2024

Garment Recovery with Shape and Deformation Priors

Pascal Fua, Benoît Alain René Guillard, Ren Li, Corentin Camille Marius Dumery

While modeling people wearing tight-fitting clothing has made great strides in recent years, loose-fitting clothing remains a challenge. We propose a method that delivers realistic garment models from real-world images, regardless of garment shape or defor ...

2024

Multilayer diffusion-barrier composites based on microfibrillated cellulose from wood, bacterial and algae sources

Aigoul Schreier

This work is driven by the effort towards increased environmental sustainability and aims to develop a new food packaging material based on renewable materials, and more specifically cellulose as the most abundant biomass resource on Earth. Focus was on mi ...

EPFL2024

Direct high-temperature growth of GaN on Si using trimethylaluminum preflow enabling vertically-conducting heterostructures

Elison de Nazareth Matioli, Alessandro Floriduz

In this work, we demonstrate that GaN can be directly grown at high temperature on Si(111) substrates by metalorganic CVD without using any intentional AlN buffer, by simply employing a trimethylaluminum (TMAl) preflow. We found that n-GaN layers directly ...

Iop Publishing Ltd2024

Data-Intensive Exploration of the Photoelectrochemical Responses of Main-Group Metal Sulfides

Nicola Colonna

Materials that efficiently promote the thermodynamically uphill water-splitting reaction under solar illumination are essential for generating carbon-free ("green") hydrogen. Mapping out the combinatorial space of potential photocatalysts for this reaction ...

Amer Chemical Soc2024

Synthesis of metal oxide-overcoated carbon materials by liquid phase ALD and their applications in catalysis

Farzaneh Talebkeikhah

Coating nano particles and other substrates for efficiency enhancement, protection and obtaining new atomic structures is a widespread research topic in catalysis and material synthesis. Thus far, different approaches of coating, ranging from simplest to s ...

EPFL2023

Transparent Porous Conductive Substrates for Gas-Phase Photoelectrochemical Hydrogen Production

Jun Ho Yum, Kevin Sivula, Linda Lazouni, Loï Charles Carbone, Benjamin Goldman, Rebekah Anne Wells, Simon Nussbaum, Marina Caroline Michèle Caretti, Elizaveta Potapova Mensi, Hannah Elizabeth Johnson, Emeline Cécile Rideau

Gas diffusion electrodes are essential components of common fuel and electrolysis cells but are typically made from graphitic carbon or metallic materials, which do not allow light transmittance and thus limit the development of gas-phase based photoelectr ...

Wiley-V C H Verlag Gmbh2023