Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Cubilot

Publications associées (10)

The role of Zn in C-S-H atomic structure, nucleation and growth

Anna Morales Melgares

The most promising solution towards cementitious materials with a lower carbon footprint is the partial substitution of the clinker by supplementary cementitious materials (SCMs) such as fly ash, blast furnace slag, limestone and calcined clays. The produc ...

EPFL2023

Report of RILEM TC 267-TRM phase 3: validation of the R-3 reactivity test across a wide range of materials

Karen Scrivener, Mohsen Ben Haha, François Henri Avet, Xuerun Li, Ruben Anton Snellings, Diana Londoño Zuluaga, Pawel Tadeusz Durdzinski, Alastair Thomas Matthew Marsh

RILEM TC 267 TRM- "Tests for Reactivity of Supplementary Cementitious Materials" recommends the Rapid Reliable Relevant (R-3) test as a method for determining the chemical reactivity of supplementary cementitious materials (SCMs) in Portland cement blends. ...

SPRINGER2022

Nanoscale modelling of ionic transport in the porous C-S-H network

Khalil Ferjaoui

To reduce the CO2 footprint of construction materials, concrete producers blend their cement with Supplementary Cementitious Materials (SCMs). SCMs such as fly ash or blast furnace slag are mostly the byproducts of other industries. And while SCMs are chos ...

EPFL2022

The effect of alkali hydroxides and equilibration time on Al uptake by calcium silicate hydrates (C-S-H)

Sonya Barzgar

Cement production accounts for approximately 8% of man-made CO2 emissions. Lowering these CO2 emissions is currently one of the most important and urgent research topics within the cement community. To reduce these emissions, the Portland cement (PC) is pa ...

EPFL2021

Reactivity tests for supplementary cementitious materials: RILEM TC 267-TRM phase 1

Karen Scrivener, Mohsen Ben Haha, Xuerun Li, Ruben Anton Snellings, Mathieu Antoni

A primary aim of RILEM TC 267-TRM: Tests for Reactivity of Supplementary Cementitious Materials (SCMs) is to compare and evaluate the performance of conventional and novel SCM reactivity test methods across a wide range of SCMs. To this purpose, a round ro ...

SPRINGER2018

Rapid screening tests for supplementary cementitious materials: past and future

Karen Scrivener, Ruben Anton Snellings

Rapid screening tests for supplementary cementitious materials (SCMs) have been in use for over 150 years. Over the years a multitude of methods have been put forward to predict the strength development of SCMblended mortars and concrete. This paper summar ...

Springer2016

The pore solution of blended cements: a review

Ruben Anton Snellings

This paper is the work of working group 3 of the RILEM Technical Committee on Hydration and Microstructure of Concrete with SCM (TC 238-SCM). The pore solution is an essential but often overlooked part of hydrated cements. The composition of the cement por ...

Springer2016

The Effect of Mg on Slag Reactivity in Blended Cements

Karen Scrivener, Ruben Anton Snellings

Blast-furnace slags are widely used as supplementary cementitious materials in blended cements because of their relatively high reactivity. This study describes the effect of substituting Ca by Mg on the reactivity of synthetic glass with similar compositi ...

Springer2014

Solution-Controlled Dissolution of Supplementary Cementitious Material Glasses at pH 13: The Effect of Solution Composition on Glass Dissolution Rates

Ruben Anton Snellings

Supplementary cementitious materials (SCMs) are widely used to partially replace portland clinker in blended cements. Reducing clinker contents further without compromising the development of early strength necessitates a better assessment and enhancement ...

Wiley-Blackwell2013

Heat treatment of carbon anodes for the aluminum industry

Mauriz Lustenberger

Aluminum is produced by the electrolytic reduction of alumina dissolved in molten cryolite. This process requires carbon anodes which are consumed during the electrolysis. The anodes contribute roughly with 15% to the total aluminum production cost. If the ...

EPFL2004