Publications related to Variable amplitude fatigue of adhesively-bonded pultruded GFRP joints

Related publications (31)

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Encapsulation strategies for mechanical impact and damp heat reliability improvement of lightweight photovoltaic modules towards vehicle-integrated applications

Fabiana Lisco

Lightweight modules are essential for next-generation vehicle-integrated photovoltaic (VIPV) applications, such as solar-powered cars, allowing integration of solar cells beyond the roof, and on the hood, boot and body panels, and thereby extending the dri ...

Elsevier2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Effect of fiber architecture on tension-tension fatigue behavior of bolted basalt composite joints

Thomas Keller, Lulu Liu

The effect of fiber architecture, i.e., unidirectional (UD) vs. multi-directional (MD), on the tension-tension fa-tigue behavior of bolted double-lap basalt composite joints was experimentally investigated. The fatigue load-life (F -N) curves of MD and UD ...

ELSEVIER SCI LTD2023

CRACK SHIELDING MECHANISMS OF INTERLAYERED EPOXY MATERIALS UNDER QUASI-STATIC AND FATIGUE LOADING

Anastasios Vassilopoulos, Dharun Vadugappatty Srinivasan

This research explores the capability of PEI and PVDF thermoplastic interlayers to arrest cracks in epoxy materials modified with short-glass fibers and core-shell rubber particles. It also investigates the effect of interlayer position, the number of inte ...

Queen's University Belfast2023

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Qianhui Yu

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

EPFL2023

Fatigue behavior and life prediction of wind turbine blade composite materials

Anastasios Vassilopoulos

Fatigue life prediction of wind turbine rotor blades is a very challenging task, as their failure is led by different failure types that act synergistically. Inherent defects like wrinkles, fiber misalignments, and voids that can be introduced during fabri ...

Woodhead Publishing (Elsevier)2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Reliable Microsecond-Scale Distributed Computing

Athanasios Xygkis

The landscape of computing is changing, thanks to the advent of modern networking equipment that allows machines to exchange information in as little as one microsecond. Such advancement has enabled microsecond-scale distributed computing, where entire dis ...

EPFL2023

Considerations on the partial safety factor format for reinforced concrete structures accounting for multiple failure modes

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu

The increasing usage of nonlinear analyses for the design of reinforced concrete structures and the necessity of codes of practice to provide a consistent safety format for them is one of the challenges that new generations of codes of practice are facing. ...

ELSEVIER SCI LTD2022

A Data-Knowledge Hybrid Driven Method for Gas Turbine Gas Path Diagnosis

Dimitrios Kyritsis, Jinzhi Lu

Gas path fault diagnosis of a gas turbine is a complex task involving field data analysis and knowledge-based reasoning. In this paper, a data-knowledge hybrid driven method for gas path fault diagnosis is proposed by integrating a physical model-based gas ...

MDPI2022

Discretization Uncertainties of Flow and Fatigue Damage Simulations of a Reversible Francis Pump-Turbine at Off-Design Operation in Turbine Mode

Drazen Dujic, Daniel Biner, Philippe Alexandre Bontemps

In the framework of the XFLEX HYDRO H2020 European Project, a 5 MW reversible Francis pump-turbine prototype, equipped with an industrial full size frequency converter, is investigated to demonstrate enhanced grid regulation capacities of variable speed hy ...

SPRINGER INTERNATIONAL PUBLISHING AG2022

Are socially-aware trajectory prediction models really socially-aware?

Alexandre Massoud Alahi, Seyed Mohsen Moosavi Dezfooli, Saeed Saadatnejad, Mohammadhossein Bahari

Our transportation field has recently witnessed an arms race of neural network-based trajectory predictors. While these predictors are at the core of many applications such as autonomous navigation or pedestrian flow simulations, their adversarial robustne ...

2022

Anchorage of shear reinforcement in beams and slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu, Frédéric Monney

Anchorage of shear reinforcement, such as links or stirrups, can be performed by providing hooks, bends or heads at their ends, by welding transverse reinforcement or by closing open stirrups with pins. Hooks and bends, also used to enhance the anchorage o ...

2022

Shear Response of Wet Weak Carbonate Rock/Grout Interfaces Under Cyclic Loading

Eleni Stavropoulou

The development and construction of offshore wind farms requires the correct estimation of the friction that can be mobilised at the rock/grout interface. In conventional studies, the shear behaviour of a joint is usually investigated with laboratory tests ...

2021

Uncertainties in the Seismic Assessment of Historical Masonry Buildings

Katrin Beyer, Igor Tomic, Francesco Vanin

Seismic assessments of historical masonry buildings are affected by several sources of epistemic uncertainty. These are mainly the material and the modelling parameters and the displacement capacity of the elements. Additional sources of uncertainty lie in ...

2021

Casting position effects on bond performance of reinforcement bars

Aurelio Muttoni, Miguel Fernández Ruiz, Francesco Rafael Alberto Moccia

The phenomena associated with the consolidation of fresh concrete (bleeding and plastic settlement) are commonly considered significant for the bond performance of reinforcement. However, rules to take care of such influence for design are not consistent a ...

ERNST & SOHN2021

Origami-inspired carbon fiber-reinforced composite sandwich materials - Fabrication and mechanical behavior

Thomas Keller

A folding fabrication method inspired by origami for carbon fiber-reinforced composites to fabricate three-dimensional structures is presented. PMI foams serve as substrates, making it possible to manufacture this kind of origami-inspired composite sandwic ...

ELSEVIER SCI LTD2021

Post-tensioning of glass beams: Analytical determination of the allowable pre-load

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

The effectiveness of post-tensioning in enhancing the fracture resistance of glass beams depends on the level of compressive pre-stress introduced at the glass edge surface that will in service be exposed to tensile stresses induced by bending. Maximum pre ...

2021

Fatigue of reinforced UHPFRC members and monitoring of fatigue action effects on bridges

Bartlomiej Wojciech Sawicki

The objective of this thesis is to develop knowledge and methods to prevent fatigue failure of bridges. The Fatigue Limit State is investigated from both the demand (S) and resistance (R) side. The S-part focuses on reduction of uncertainties through monit ...

EPFL2021