Publications related to Effect of Pre-straining, Activation Temperature and Thermomechanical Training on Recovery Behavior of Femnsi Based Sma

Related publications (21)

Micromechanics reveal strain rate dependent transition between dislocation mechanisms in a dual phase high entropy alloy

An equimolar NiCoFeCrGa high entropy alloy having dual-phase composition was studied, where the constituent phases exhibit distinct mechanical properties. Micropillars with various diameters were created from two differently heat treated samples, then they ...

2025

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Development and characterization of thin iron-based shape memory alloy prestressing wire

Meet Jaydeepkumar Oza

Iron-based shape memory alloys (Fe-SMA) have been used successfully in the previous years as prestressing reinforcement in the form of rebars, rods and flat strips, for various types of structural elements and loading scenarios. This paper introduces a new ...

Elsevier B.V.2024

Effects of beam shaping on copper-steel interfaces in multi-material laser beam powder bed fusion

Seyed Amirmohammad Jamili

Multi-material laser beam powder bed fusion (PBF-LB) is a promising approach to meet industrial demands for multifunctional components, due to its enhanced freedom of design. Copper and stainless steel are interesting materials to be combined due to the hi ...

Elsevier Science Sa2024

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

Elastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

This paper discusses the influence of fiber orientation on elastic limit tensile stress of ultra-high performance fiber reinforced cementitious composites (UHPFRC). An original model relating elastic limit tensile stress to fiber orientation is proposed, a ...

2023

Micromechanics of oxide inclusions in ferrous alloys

Alejandra Inés Slagter

Oxide inclusions are inevitably present in steel as a direct consequence of the steelmaking process; as a result, a cubic centimetre of modern steel will generally contain about a million of these hard and brittle micrometre-sized ceramic particles. Inclus ...

EPFL2023

An investigation on reorientation and textural evolution in a martensitic NiTi rolled sheet using EBSD

Roland Logé, Cyril Cayron, Junfeng Xiao

Variant reorientation is a ubiquitous phenomenon in shape memory alloys and has a great influence on their texture and mechanical response. In the present study, a martensitic NiTi rolled sheet is investigated by the electron backscattering diffraction (EB ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Deformation twinning mechanism in magnesium at the microscale: strain rate, temperature and orientation effects

Nicolò Maria Della Ventura

The project aims to validate some recent theoretical developments on the deformation twinning nucleation mechanism in HCP metals through small-scale mechanic experiments. To this end, a systematic investigation of the mechanical response of pure magnesium ...

EPFL2022

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

Roland Logé, Cyril Cayron, Baptiste Thomas Jean Rouxel

Cu-Be alloys provide excellent electrical and mechanical properties, but present serious health hazards during manufacturing. Among alternative alloys, the Cu-Ti system has the highest yield strength; however, Ti cannot be easily solutionized at concentrat ...

ELSEVIER SCI LTD2022

A Review of the Use of UHPFRC in Bridge Rehabilitation and New Construction in Switzerland

Eugen Brühwiler, Emmanuel Denarié, Numa Joy Bertola, Philippe Schiltz

Ultra-High-Performance Fibre Reinforced Cementitious Composite (UHPFRC) provides solutions to enhance existing structures and design innovative new structures. Structural UHPFRC offers 3–5 times higher compressive and tensile strengths than ordinary concre ...

2021

Yielding of a quartz sand from saturated to dry state

Alessio Ferrari

The paper presents the results of an experimental work where we analyse the behaviour of an unsaturated quartz sand in a wide range of degree of saturation (from saturated to dry state). The possibility of anticipating the hydro-mechanical behaviour of the ...

E D P SCIENCES2020

Pressure-Induced Enlargement and Ionic Current Rectification in Symmetric Nanopores

Aleksandra Radenovic, Michal Daniel Macha, Sanjin Marion, Andrey Chernev, Sebastian James Davis

Nanopores in solid state membranes are a tool able to probe nanofluidic phenomena or can act as a single molecular sensor. They also have diverse applications in filtration, desalination, or osmotic power generation. Many of these applications involve chem ...

2020

In situ characterization of work hardening and springback in grade 2 alpha-titanium under tensile load

Helena Van Swygenhoven

Plastic effects during sheet metal forming can lead to undesirable distortions in formed components. Here, the three-stage work hardening and plastic strain recovery ("springback") in a cold-rolled, alpha-phase commercially pure titanium is examined. Inter ...

2019

In situ characterization of a high work hardening Ti-6Al-4V prepared by electron beam melting

Helena Van Swygenhoven, Nicola Casati, Karl Alan Sofinowski

A multi-phase Ti-6Al-4V prepared by electron beam melting and thermal post treatments has been shown to exhibit increased strength and ductility over standard wrought or hot isostatic pressed Ti-6-Al-4V. The mechanical improvements are due to a prolonged, ...

2019

Electrical energy generated by silicone elastomers filled with nanospring- carbon- nanotubes

Frank Nüesch

Dielectric elastomer generators (DEGs) are flexible capacitors that convert mechanical into electrical energy. They rely on an external voltage source to charge the capacitor during each operation cycle. An alternative to this is an autonomous DEG which op ...

Royal Society of Chemistry2019

Designing high ductility in magnesium alloys

William Curtin, Binglun Yin, Rasool Ahmad

The thermally activated pyramidal-to-basal (PB) transition of (c + a) dislocations, transforming glissile pyramidal dissociated core structures into sessile basal dissociated ones, lies at the origin of low ductility in pure magnesium (Mg). Solute-accelera ...

PERGAMON-ELSEVIER SCIENCE LTD2019

Next generation UHPFRC for sustainable structural applications

Emmanuel Denarié, Amir Hajiesmaeili

Over the last few decades, ever-increasing demands of society to the built environment have continually increased consumption of energy and materials for the construction and maintenance of structures. Meanwhile, Strain Hardening Ultra High-Performance Fib ...

2018

Early Stages of Precipitation In Aluminum Alloys by First-Principles and Machine-Learning Atomistic Simulations

Daniele Giofré

Age hardening induced by the formation of (semi)-coherent precipitate phases is crucial for the processing and final properties of the widely used Al-6000 alloys despite the early stages of precipitation are still far from being fully understood. This cruc ...

EPFL2018