Publications by Antonin Faes | EPFL Graph Search

Related publications (42)

Accurate color characterization of solar photovoltaic modules for building integration

Christophe Ballif, Antonin Faes, Alessandro Francesco Aldo Virtuani, Jordi Escarre Palou, Alejandro Borja Block

Accurate and reproducible color characterization is essential for colored building integrated photovoltaic products, both for manufacturing quality control and assessing long-term color stability. However, existing characterization techniques struggle to a ...

Pergamon-Elsevier Science Ltd2023

Enhancing lifetime, forecasting, and economic benefits of photovoltaic technologies undergoing UV-induced degradation with optical filtering

Christophe Ballif, Antonin Faes, Christian Michael Wolff, Marion Solange Madeleine Dussouillez

Ultraviolet-induced degradation (UV-ID) of various PV cell types was analyzed under optical UV filters with different cutoff wavelengths. Cell types studied included interdigitated back contact (IBC), passivated emitter and rear totally diffused (PERT), an ...

2025

Field test and electrode optimization of electrodynamic cleaning systems for solar panels

Christophe Ballif, Aïcha Hessler-Wyser, Matthieu Despeisse, Nicolas Würsch, Antonin Faes, Jacques Levrat

Soiling is the major cause of power loss of photovoltaics (PV) and concentrated solar power (CSP) in desert areas. Electrodynamic cleaning system (EDS) is an automatic and water-free integrated cleaning system for mirrors or solar panels, which uses pulsed ...

WILEY2019

Compilation of mechanical properties for the structural analysis of solid oxide fuel cell stacks. Constitutive materials of anode-supported cells

Jan Van Herle, Antonin Faes, Arata Nakajo

The mechanical failure of one cell is sufficient to lead to the end of service of a solid oxide fuel cell (SOFC) stack. Therefore, there is growing interest in gaining knowledge on the mechanical properties of the cell materials for stress analysis. This s ...

2012

RedOx study of anode supported solid oxide fuel cell

Jan Van Herle, Aïcha Hessler-Wyser, Antonin Faes, Arata Nakajo

The common technology for solid oxide fuel cells (SOFC) is based on a cermet (ceramic-metal composite) anode of nickel with yttria stabilized zirconia (YSZ), often used as the supporting structure. One of the main limitations of this technology is the tole ...

2009

Fabrication of structured anode-supported solid oxide fuel cell by powder injection molding

Jan Van Herle, Antonin Faes, Zacharie Wuillemin

Powder Injection Molding (PIM) gives the possibility to produce, at an industrial rate, ceramic parts with fine details. It is thus a possible approach to reduce the fabrication costs of Solid Oxide Fuel Cells (SOFCs). This work presents fabrication and el ...

2013

Characterization of Lightweight Polymeric Honeycomb Structures for Use as Backsides in Glass‐Free PV Modules

Christophe Ballif, Antonin Faes, Umang Bhupatrai Desai

In densely populated or mountainous countries where installation of large‐scale solar plants is challenging, photovoltaic (PV) modules in building applications offer a solution by transforming passive surfaces into energy‐generating systems. The need for f ...

Wiley2025

RedOx Stability of Anode Supported Solid Oxide Fuel Cells

Antonin Faes

The weakness of nickel-based solid oxide fuel cell anodes is their low ability to withstand re-oxidation at working temperature, especially for the anode-supported cell design. The volume expansion coming along with nickel (Ni) oxidation induces stresses i ...

EPFL2011

Novel Mechanically Robust and Environmentally Stable Light‐Weight Colored Photovoltaic Modules Based on Composite Polymer Backsheets

Christophe Ballif, Antonin Faes, Umang Bhupatrai Desai, Marie Amélie Camille Courtant

Reliable and esthetically pleasing lightweight photovoltaic modules for building integration are expected to grow interest in the consumer market, especially for retrofitting older buildings and storehouses that are not structurally designed to withstand a ...

Wiley2025

The in vivo performance of magnetic particle-loaded injectable, in situ gelling, carriers for the delivery of local hyperthermia

Heinrich Hofmann, Alke Fink, Antonin Faes

In situ forming implants are attractive for minimally invasive localized therapies such as aneurysm embolization. As for the superparamagnetic iron oxide nanoparticles (SPIONs), their deposition/injection in a target tissue area allows magnetically induced ...

2010

Strength of Anode-Supported Solid Oxide Fuel Cells

Antonin Faes

Nickel oxide and yttria doped zirconia composite strength is crucial for anode-supported solid oxide fuel cells, especially during transient operation, but also for the initial stacking process, where cell curvature after sintering can cause problems. This ...

Wiley-Blackwell2011

Experimental and Theoretical Investigation of Degradation Mechanisms in SOFC Electrodes

Jan Van Herle, Christos Comninellis, Aïcha Hessler-Wyser, Antonin Faes, Pietro Tanasini

Performance degradation data obtained on single solid oxide fuel cells tested at 850°C with air and humidified H2 and using Ni-YSZ anode supported cells are presented. Microscopic investigation is carried out on both anode and cathode to quantify variation ...

2009

A comparative performance analysis of stand-alone, off-grid solar-powered sodium hypochlorite generators

Demetri Psaltis, Christophe Moser, Antonin Faes, Miguel Antonio Modestino, Enrico Chinello

Sodium hypochlorite (NaClO) is a chemical commodity widely employed as a disinfection agent in water treatment applications. Its production commonly follows electrochemical routes in an undivided reactor. Powering the process with photovoltaic (PV) electri ...

2019

In situ Reduction and Oxidation of Nickel from Solid Oxide Fuel Cells in a Transmission Electron Microscope

Jan Van Herle, Aïcha Hessler-Wyser, Quentin Thomas Jeangros, Antonin Faes

Environmental transmission electron microscopy was used to characterize in situ the reduction and oxidation of nickel from a Ni/YSZ solid oxide fuel cell anode support between 300-500°C. The reduction is done under low hydrogen pressure. The reduction init ...

2009

X-ray Imaging and Analysis of 3D Microstructural Changes in Aged Ni-YSZ Anode

Jan Van Herle, Aïcha Hessler-Wyser, Antonin Faes

Ni-YSZ anode supports were used to fabricate test cells composed of yttria-stabilised zirconia (YSZ) electrolyte and lanthanum strontium ferrite (LSF) or lanthanum strontium manganite (LSM) / YSZ cathodes. These cells were operated at 720 °C at an average ...

2011

Quantifying and modeling the impact of interconnection failures on the electrical performance of crystalline silicon photovoltaic modules

Christophe Ballif, Antonin Faes, Jacques Levrat, Alessandro Francesco Aldo Virtuani, Matthieu Despeisse, Fanny Sculati-Meillaud, Eleonora Annigoni

Failures in the metallic interconnections are among the main degradation modes for photovoltaic modules. Fatigue accumulation due to thermomechanical stresses can result in deterioration of the solder joints or in broken ribbons. In this paper, we first qu ...

2019

Stress tolerance of lightweight glass-free PV modules for vehicle integration

Kléber Nicolet-dit-Félix, Christophe Ballif, Matthieu Despeisse, Aïcha Hessler-Wyser, Jacques Levrat, Antonin Faes, Gianluca Cattaneo, Umang Bhupatrai Desai, Fahradin Mujovi

Electric vehicles (EVs) currently dominate the sales in the automotive market. A big leap in this market can be made by developing a photovoltaic product that can be integrated to an EV, as it can boost the driving range of the EV while reducing the chargi ...

Edp Sciences S A2024

Three-dimensional microstructural changes in the Ni-YSZ solid oxide fuel cell anode during operation

Jan Van Herle, Aïcha Hessler-Wyser, Antonin Faes

Microstructural evolution in solid oxide fuel cell (SOFC) cermet anodes has been investigated using X-ray nanotomography along with differential absorption imaging. SOFC anode supports composed of Ni and yttria-stabilized zirconia (YSZ) were subjected to e ...

2012

An accurate bifacial PV module energy performance model using a direct-diffuse power rating model

Antonin Faes

Predicting the energy output of a bifacial photovoltaic (PV) module is usually not as straightforward as for a monofacial module. The problem usually lies in the estimation of the back-side irradiance which strongly depends on the mounting conditions, trac ...

ELSEVIER SCI LTD2025

Design of experiment approach applied to reducing and oxidizing tolerance of anode supported solid oxide fuel cell. Part I: Microstructure optimization

Jan Van Herle, Aïcha Hessler-Wyser, Antonin Faes, Jean-Marie Fuerbringer

The main drawback of Ni/YSZ anode supports for solid oxide fuel cell application is their low tolerance to reducing and oxidizing (RedOx) atmosphere changes, owing to the Ni/NiO volume variation. This work describes a structured approach based on design of ...

Elsevier2011