Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Lecture

Dynamics of Mechanical Systems

In course

ME-311: Dynamical effects in mechanical design

Ce cours poursuit la compréhension des effets cinématiques et dynamiques de systèmes mécaniques complexes et introduit les bases pour les comprendre et les modéliser. L'étudiant saura expliquer et modéliser la dynamique et choisir des modèles adéquats. ...

Description

This lecture covers the dynamics of mechanical systems during start-up, focusing on the evolution of speed, kinetic energy, and synchronization time. It also discusses braking mechanisms such as friction, aerodynamic, and eddy brakes, highlighting the energy dissipation and heating issues.

This video is available exclusively on Mediaspace for a restricted audience. Please log in to MediaSpace to access it if you have the necessary permissions.

Watch on Mediaspace

Instructor

Jürg Alexander Schiffmann

After obtaining his diploma in mechanical engineering from EPFL in 1999 he co-founded a start-up company dedicated to the design of gas bearing supported rotors. In 2005 he joined Fischer Engineering Solutions where he led the development of small-scale, gas bearing supported high-speed turbomachinery for fuel cell air supplies and for domestic scale heat pumps. In parallel he worked on his PhD, which he obtained from EPFL in 2008 and for which he was awarded the SwissElectric Research Award. He then joined the Gas Turbine Lab at MIT as a postdoctoral associate where he worked on foil bearings and on the experimental investigation of radial diffusers. In 2013 he was nominated assistant professor at the Ecole Polytechnique Fédérale de Lausanne where he founds the Laboratory for Applied Mechanical Design. His current research interest are in gas lubricated bearings, in aerodynamics of small-scale compressors and turbines and in automated design and optimization methodologies.

Official source

Related concepts (12)

Brake

A brake is a mechanical device that inhibits motion by absorbing energy from a moving system. It is used for slowing or stopping a moving vehicle, wheel, axle, or to prevent its motion, most often accomplished by means of friction. Most brakes commonly use friction between two surfaces pressed together to convert the kinetic energy of the moving object into heat, though other methods of energy conversion may be employed. For example, regenerative braking converts much of the energy to electrical energy, which may be stored for later use.

Hydraulic brake

A hydraulic brake is an arrangement of braking mechanism which uses brake fluid, typically containing glycol ethers or diethylene glycol, to transfer pressure from the controlling mechanism to the braking mechanism. During 1904, Frederick George Heath (Heath Hydraulic Brake Co., Ltd.), Redditch, England devised and fitted a hydraulic (water/glycerine) brake system to a cycle using a handlebar lever and piston. He obtained patent GB190403651A for “Improvements in hydraulic actuated brakes for cycles and motors”, as well as subsequently for improved flexible rubber hydraulic pipes.

Disc brake

A disc brake is a type of brake that uses the calipers to squeeze pairs of pads against a disc or a "rotor" to create friction. This action slows the rotation of a shaft, such as a vehicle axle, either to reduce its rotational speed or to hold it stationary. The energy of motion is converted into waste heat which must be dispersed. Hydraulically actuated disc brakes are the most commonly used form of brake for motor vehicles, but the principles of a disc brake are applicable to almost any rotating shaft.

Brake-by-wire

Brake-by-wire technology in the automotive industry is the ability to control brakes through electronic means, without a mechanical connection that transfers force to the physical braking system from a driver input apparatus such as a pedal or lever. The three main types of brake-by-wire systems are: electronic parking brakes which have, since the turn of the 21st century, become more common; electro-hydraulic brakes (EHB) which can be implemented alongside legacy hydraulic brakes and as of 2020 have found small-scale usage in the automotive industry; and electro-mechanical brakes (EMB) that use no hydraulic fluid, which as of 2020 have yet to be successfully introduced in production vehicles.

Drum brake

A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward against a rotating cylinder-shaped part called a brake drum. The term drum brake usually means a brake in which shoes press on the inner surface of the drum. When shoes press on the outside of the drum, it is usually called a clasp brake. Where the drum is pinched between two shoes, similar to a conventional disc brake, it is sometimes called a pinch drum brake, though such brakes are relatively rare.

Related lectures (9)

Mechanical Power Transmission: Gears and Couplings

Provides an overview of mechanical power transmission principles, focusing on gears and couplings in engineering applications.

Thruster-based Attitude Control MOOC: Space Mission Design and Operations

Covers the design and operation of thruster-based attitude control systems for spacecraft.

In-wheel Integration: EPFLRT

Explores the integration of dedicated motors in each wheel for enhanced car performance.

Eddy Currents: Maxwell Equations and Practical Examples MOOC: Electromechanical conversion I

Delves into eddy currents, their origins, and practical applications in braking systems and energy losses in conductors.

Mechanism Design: Basics and Applications Log in to Mediaspace to watch this video