Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Unité

Laboratoire des matériaux organiques et macromoléculaires

Laboratoire

Publications associées (30)

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

Near-Room-Temperature Detection of Aromatic Compounds with Inkjet-Printed Plasticized Polymer Composites

Jürgen Brugger, Thomas Maeder, Mohammadmahdi Kiaee

Chemiresistive gas sensors composed of a thermoplastic polymer matrix and conductive fillers offer various advantages for detecting volatile organic compounds (VOCs), including low power consumption due to near-room-temperature operation, high sensitivity, ...

Amer Chemical Soc2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Soft Mechanochemistry of Disulfide-Crosslinked Polymer Networks

Zhao Meng

Mechanochemistry harnesses mechanical force to facilitate chemical reactions. Traditionally, the field of polymer mechanochemistry has used methods to activate chemical bonds, which use forces that are larger than those that are required to break a covalen ...

EPFL2024

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Supramolecular Modifications of Semicrystalline Polymers

Michael Alan Giffin

Supramolecular interactions play an important role in defining the structure and the resulting mechanical properties of materials. For instance, interchain hydrogen-bonding in PAs gives them superior strength and stiffness in engineering materials, while t ...

EPFL2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Bottlebrush Dielectric Elastomers with Improved Properties for Actuation

Yeerlan Adeli

Dielectric elastomer actuators (DEA) are elastic capacitors composed of a pair of compliant electrodes and a soft dielectric elastomer film sandwiched in between. This kind of stretchable capacitors can be actuated when charged, can generate electricity fr ...

EPFL2023

Reinforced Supramolecular Networks of End Functionalized Polymers for Tailored Thermomechanical Property Profiles

Yevhen Hryshunin

Thermoset rubbers give rise to elastomers with tunable stiffness and high resilience but are not recyclable. Thermoplastic elastomers can address this problem but their broad applicability is impeded by either limited operating temperatures or inferior ela ...

EPFL2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Influence of the molecular weight and physical properties of a thermoplastic polymer on its dynamic wetting behavior

Valentin Rougier

The wetting dynamics of molten thermoplastic polymers, which are known to influence the force balance of the triple line, are not understood properly despite their importance in many industrial processes. In particular, the influence of the molecular weigh ...

Elsevier2023

Supramolecular Polymer Brushes

Friederike Katharina Metze

Thin polymer coatings present a method to modify the surface properties of underlying substrates. Polymer-coated surfaces have been used as anticorrosive materials, surfaces with special wetting properties, antifriction materials, and as materials for biom ...

EPFL2023

Recyclable flame retardant phosphonated epoxy based thermosets enabled via a reactive approach

Véronique Michaud, Valentin Rougier

The development of reusable fire-safe polymers with a prolonged lifetime heralds the switch for a transition towards circular economy. In this framework, we report a novel phosphonated thermoset which is composed of networked phosphonate esters containing ...

ELSEVIER SCIENCE SA2023

In Situ and Time-Resolved Transmission Electron Microscopy of Nanoscale Processes

Chengcheng Yan

Observing the fast dynamics of nanoscale systems is crucial in order to understand and ultimately control their behavior. Characterizing these dynamic processes requires techniques with atomic spatial resolution and a temporal resolution that matches the t ...

EPFL2023

Strategies for energy-efficient frontal polymerisation processing and microstructural evaluation of fibre reinforced composites

Jacobus Gerardus Rudolph Staal

Liquid composite moulding methods are widely applied for manufacturing of fibre reinforced polymer (FRP) composites and consist of two main stages: impregnation of fibrous reinforcements by a liquid monomer resin and curing of this resin. This thesis work ...

EPFL2023

Semiconductor-based device architectures in multimaterial fibers

William Nicolas Duncan Esposito

Semiconductor materials have given rise to today's digital technology and consumer electronics. Widespread adoption is closely linked to the ability to process and integrate them in devices at scale. Where flexibility and large surfaces are required, such ...

EPFL2023

Architecturally Diverse Polymer Brushes Prepared via Surface-Initiated Atom Transfer Radical Polymerization

Sabrina Sant-Greber

Polymer brushes, which are polymers anchored to a solid substrate by one chainend, have the ability to modify the properties of an underlying substrate, offering intriguing features such as enhanced lubrication, reduced friction, colloidal stability, and a ...

EPFL2023