Publications associées à Mechanical properties of replicated cellular Zn and Zn1.5Mg in uniaxial compression

Publications associées (26)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Computational Homogenization for Inverse Design of Surface-based Inflatables

Mark Pauly, Florin Isvoranu, Francis Julian Panetta, Yingying Ren, Seiichi Eduardo Suzuki Erazo, Uday Kusupati

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

Association for Computing Machinery (ACM)2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Design for demise applied to spacecraft structural panels and experiments for ClearSpace One platform

Alexandre Achille Looten

With growing awareness of the vulnerability of the near-Earth space region and the anticipated surge in satellite objects, efforts are underway to assess and implement various mitigation strategies. These aim to minimize the impact of space activities and ...

EPFL2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Roland Logé, Cyril Cayron, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Influence of Fiber Orientation on the Elastic Limit Tensile Stress of UHPFRC

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

The elastic limit tensile stress of UHPFRC is governed by contributions of the cementitious matrix and the fibrous skeleton. This paper finds that fiber orientation has significant influence on the matrix tensile strength of UHPFRC, while this is not consi ...

2023

Modeling the mechanics and rheology of porous and granular media: an elastoplastic continuum approach

Lars Kristoffer Uhlen Blatny

The complex mechanics of porous and granular media play a significant role in various industrial processes and natural phenomena. As an example, understanding the mechanics of how failure occurs, localizes and propagates in porous brittle solids under vari ...

EPFL2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

Supramolecular Modifications of Semicrystalline Polymers

Michael Alan Giffin

Supramolecular interactions play an important role in defining the structure and the resulting mechanical properties of materials. For instance, interchain hydrogen-bonding in PAs gives them superior strength and stiffness in engineering materials, while t ...

EPFL2023

Elastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

This paper discusses the influence of fiber orientation on elastic limit tensile stress of ultra-high performance fiber reinforced cementitious composites (UHPFRC). An original model relating elastic limit tensile stress to fiber orientation is proposed, a ...

2023

Role of Minimum Adhesive Wear Particle Size in Third-Body Layer Properties

Jean-François Molinari, Son-Jonathan Pham-Ba

We employ a novel discrete element method (DEM) force formulation to simulate adhesive wear and assess the effects of material and loading parameters on the properties of the third-body layer (TBL) formed during sliding motion. The study emphasizes the rol ...

2023