Publication

An Instrumented High-Speed Rotor with Embedded Telemetry for The Continuous Spatial Pressure Profile Measurement in Gas Lubricated Bearings: A Proof of Concept

Publications associées (29)

Integrated Electronics for Deep Implants to Remotely Monitor Hemodynamics

The integration of technology in the medical field has greatly improved accuracy in diagnoses, thus leading to more effective treatments. Wearable and implantable medical devices offer great potential for remote patient monitoring, particularly for heart f ...

EPFL2023

Triple Crossed Flexure Pivot Based on a Zero Parasitic Center Shift Kinematic Design

Simon Nessim Henein, Etienne Frédéric Gabriel Thalmann

Thanks to their absence of play, absence of contact friction and possible monolithic fabrication, flexure pivots offer advantages over traditional bearings in small-scale, high accuracy applications and environments where lubrication and wear debris are pr ...

2022

Reinforcing hydrogels with in situ formed amorphous CaCO3

Michael David Kessler, Huachuan Du, Esther Amstad, Matteo Hirsch, Ran Zhao, Tianyu Yuan

Hydrogels are often employed for tissue engineering and moistening applications. However, they are rarely used for load-bearing purposes because of their limited stiffness and the stiffness-toughness compromise inherent to them. By contrast, nature uses hy ...

ROYAL SOC CHEMISTRY2022

Experimental Investigation of Enhanced Grooves for Herringbone Grooved Journal Bearings

Jürg Alexander Schiffmann, Patrick Hubert Wagner, Philipp Kaspar Bättig

This paper presents the results of a theoretical and experimental investigation of the potential of enhanced groove geometries to increase the bearing clearance of a Herringbone Grooved Journal Bearing (HGJB) supported rotor. The theoretical study investig ...

2022

Mechanical reinforcement of granular hydrogels

Alvaro Lino Boris Charlet, Esther Amstad, Francesca Bono

Granular hydrogels are composed of hydrogel-based microparticles, so-called microgels, that are densely packed to form an ink that can be 3D printed, injected or cast into macroscopic structures. They are frequently used as tissue engineering scaffolds bec ...

ROYAL SOC CHEMISTRY2022

Overflow pressure characterization in lined plunge pools for slab sizing

Giovanni De Cesare, Pedro Filipe De Almeida Manso, Francisca Marco Cutillas

This study presents an experimental work on dynamic pressures at the bottom of a lined plunge pool that receives overflow rectangular impinging jets and aims at improving the design criteria for pool slabs. The experiments were conducted in a fairly large ...

International Association for Hydro-Environment Engineering and Research (IAHR)2022

Improving the Accuracy of Fracture Toughness Measurement in Burst Experiments

Guanyi Lu, Yixuan Zhang

Experimental studies suggest that the fracture toughness of rocks increases with the confining pressure. Among many methods to quantify this dependency, a so-called burst experiment (Abou-Sayed, 1978) may be the most widely applied in practice. Its thick w ...

SPRINGER WIEN2022

Experimental and numerical investigation of the unbalance behavior of rigid rotors supported by spiral-grooved gas journal bearings

Jürg Alexander Schiffmann, Elia Iseli

The forced response of rigid rotors, supported by herringbone-grooved gas journal bearings are investigated numerically and experimentally. The rotor configurations are varied by using end cylinders, attached at both sides of the shaft. Three rotors with d ...

ACADEMIC PRESS LTD- ELSEVIER SCIENCE LTD2022

Bottom-Pressure Development Due to an Abrupt Slope Reduction at Stepped Spillways

Anton Schleiss, José Pedro Gamito de Saldanha Calado Matos, Michael Pfister, Mohammad Javad Ostad Mirza

Fluctuating bottom-pressures on stepped chutes are relevant for the spillway design. An abrupt slope reduction causes a local alteration of the bottom-pressure development. Little information is available regarding the air–water flow properties near an abr ...

2022