Publications associées à Mesure du frottement intérieur de l'or écroui et irradié aux neutrons sur une installation travaillant dans le domaine du kilohertz

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Technosignatures Longevity and Lindy's Law

Claudio Grimaldi

The probability of detecting technosignatures (i.e., evidence of technological activity beyond Earth) increases with their longevity, or the time interval over which they manifest. Therefore, the assumed distribution of longevities has some bearing on the ...

Iop Publishing Ltd2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Lattice Green's function method for Atomistic/Continuum coupling

Ankit Gupta

Metal plasticity is an inherently multiscale phenomenon due to the complex long-range field of atomistic dislocations that are the primary mechanism for plastic deformation in metals. Atomistic/Continuum (A/C) coupling methods are computationally efficient ...

EPFL2023

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen, Tong Guo

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar, Sergio Perosanz Amarillo

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

A low-temperature prismatic slip instability in Mg understood using machine learning potentials

William Curtin, Xin Liu, Binglun Yin, Tao Liu

Prismatic slip in magnesium at temperatures T

PERGAMON-ELSEVIER SCIENCE LTD2023

Nanoindentation of embedded particles

Andreas Mortensen, Alejandra Inés Slagter, Joris Pierre Everaerts

We address the effect of elastic inhomogeneity on elastic modulus and hardness determinations made by depth-sensing indentations performed on individual particles embedded within a matrix of different elastic modulus. Finite element simulations and nanoind ...

SPRINGER HEIDELBERG2023

Interactions of Cavitation Bubbles with Deformable Interfaces

Armand Baptiste Sieber

Cavitation is a topic that has long been of interest due to the large and growing range of applications associated with it. This is mainly because the collapse of cavitation bubbles releases a considerable amount of energy into the surrounding environment. ...

EPFL2023

Laser powder bed fusion of Fe-based shape memory alloys for novel structural metamaterials and "smart" structures

Irene Ferretto

Laser powder bed fusion (LPBF) is a powder-based additive manufacturing (AM) technique, which shows great potential in the production of complex-shaped parts with unprecedented design freedom. In addition, it allows for an active manipulation of the micros ...

EPFL2023

Microstructure et usinabilité d'alliages de titane béta-métastable

Loïc Favre

Titanium has become in recent years an interesting material in many applications that require a combination of high mechanical properties and low density. It has the peculiarity of undergoing an allotropic transformation at 882°C. Below this temperature, ...

EPFL2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Modeling the mechanics and rheology of porous and granular media: an elastoplastic continuum approach

Lars Kristoffer Uhlen Blatny

The complex mechanics of porous and granular media play a significant role in various industrial processes and natural phenomena. As an example, understanding the mechanics of how failure occurs, localizes and propagates in porous brittle solids under vari ...

EPFL2023

EBSD study of variant reorientation, texture, and twin formation in a martensitic NiTi alloy deformed in compression

Mathijs Pieter van der Meer, Cyril Cayron, Roland Logé, Junfeng Xiao

Martensitic crystallography plays a vital role in the texture evolution and mechanical properties in Nickel-Titanium (NiTi) shape memory alloys when subjected to deformation. However, their microstructural changes during deformation are not well known and ...

Pergamon-Elsevier Science Ltd2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023