Publications associées à About Initial Solidification In Continuous Casting Of Steel

Publications associées (30)

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

Dimitrios Lignos

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

2023

Small-scale turbopumps for waste heat recovery applications based on an organic Rankine cycle: a study from pre-design to experimental validation

Sajjad Zakeralhoseini

The organic Rankine cycle (ORC) system is among the technologies applied to exploit waste heat in vehicles. Since common organic fluids have lower latent heat than water, higher mass flow rates are required to convert the same waste heat, considerably incr ...

EPFL2023

Origin of the enhanced pseudo-elasticity of additively manufactured Fe-17Mn-5Si-4Ni-10Cr-(V, C) shape memory alloy fabricated by laser powder bed fusion

Christian Leinenbach, Irene Ferretto

This study investigated the origin of the enhanced pseudo-elasticity of additively manufactured vanadium carbide-containing Fe-based shape memory alloys. The aged samples with two different starting microstructures, as-built and solution-treated, showed co ...

Elsevier Science Sa2023

Permeability sets the linear path instability of buoyancy-driven disks

François Gallaire, Pier Giuseppe Ledda, Giuseppe Antonio Zampogna

The prediction of trajectories of buoyancy-driven objects immersed in a viscous fluid is a key problem in fluid dynamics. Simple-shaped objects, such as disks, present a great variety of trajectories, ranging from zig-zag to tumbling and chaotic motions. Y ...

Cambridge University Press2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023

Effect of post-heat treatment conditions on shape memory property in 4D printed Fe-17Mn-5Si-10Cr-4Ni shape memory alloy

Christian Leinenbach, Irene Ferretto

The influence of post-heat treatment on the microstructure and properties of 4D printed Fe-17Mn-5Si-10Cr-4Ni (wt. %) shape memory alloy (SMA) produced via a laser powder bed fusion process is investigated in this study. It is shown that heat-treatment temp ...

2022

Non-destructive Prediction of the Buckling Load of Cylindrical Shells

Emilio José Lozano Vazquez

The current research focuses on the prediction of the maximum axial compression load a cylindrical shell is able to bear. This maximum axial compression load is the value at which a cylindrical shell loses stability and abruptly buckles. After the buckling ...

EPFL2022

Gazebo Fluids: SPH-based simulation of fluid interaction with articulated rigid body dynamics

Auke Ijspeert, Wei Wang, Jonathan Patrick Arreguit O'Neill

Physical simulation is an indispensable component of robotics simulation platforms that serves as the basis for a plethora of research directions. Looking strictly at robotics, the common characteristic of the most popular physics engines, such as ODE, DAR ...

IEEE2022

APT/TEM characterization of the element segregation in ferritic/martensitic steels after irradiation in SINQ

Lijuan Cui

Ferritic /martensitic (FM) steels are among the most important materials in various nuclear applications. As radiation-induced segregation (RIS) is one of the major factors for embrittlement of nuclear materials, thereofre it is essential to study the RIS ...

EPFL2021

Characterization of untransformed ferrite in 10Cr and 12Cr ODS steels

Roland Logé

Two new ferrito-martensitic oxide dispersion strengthened (ODS) steels reinforced with (Y, Ti, O) nanoparticles were elaborated using a high-energy attritor. The milled powder was consolidated by hot extrusion at 1050 degrees C. The two types of ODS steels ...

ELSEVIER SCI LTD2021

Enhancement of riveted steel bridges by adding a trough in UHPFRC acting in composite action

Eugen Brühwiler

Riveted railway bridges are commonly considered as being “old”, having fatigue damage and are therefore replaced. While this practice should be by now obsolete by using novel engineering methods like structural monitoring, prolongation of the service durat ...

Taylor & Francis2021

Reduced-order Models for Simulating Coupled Geometric Instabilities in Steel Beam-columns Under Inelastic Cyclic Straining

Alexander Riley Hartloper

Numerical models that can simulate coupled geometric instabilities in steel beam-columns are required for the seismic assessment of certain steel moment-resisting frames. Reliably simulating coupled instabilities requires that the steel material is precise ...

EPFL2021

Microstructural Evolution Study of Fe-Mn-Al-C Steels Through Variable Thermomechanical Treatments

Roland Logé

The microstructural evolution of the two austenitic alloys Fe-20Mn-3Al-0.7C wt pct and Fe-20Mn-6Al-0.7C wt pct when different thermal and thermomechanical treatments are performed has been studied. To this end, a generic industrial die of 100 ton capacity ...

SPRINGER2021

Cyclic metal plasticity model parameters with limited information: a constrained optimization approach

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Alexander Riley Hartloper

Tensile test data for structural steels are ubiquitous. Yet, the information monotonic loading provides with respect to the material's characteristics is limited. Notably, features of inelastic response to cyclic loading, such as the Bauschinger eect, can ...

2021

Data-Driven Reduced-Order Modeling of Convective Heat Transfer in Porous Media

Carlo Fiorina

This work presents a data-driven Reduced-Order Model (ROM) for parametric convective heat transfer problems in porous media. The intrusive Proper Orthogonal Decomposition aided Reduced-Basis (POD-RB) technique is employed to reduce the porous medium formul ...

MDPI2021

The effect of stress triaxiality on the phase transformation in transformation induced plasticity steels: Experimental investigation and modelling the transformation kinetics

Helena Van Swygenhoven, Nicola Casati

In situ multiaxial loading during neutron diffraction tests were undertaken on a low-alloyed Quenched and Partitioning (Q&P) Transformation Induced Plasticity (TRIP) Bainitic Ferrite (TBF) steel with dispersed austenite particles. The effect of stress tria ...

2021

Solute-dislocation interactions and creep-enhanced Cu precipitation in a novel ferritic-martensitic steel

Roland Logé, Cyril Cayron

G115 steel has gained a growing interesting recently for its use in next-generation ultra-supercritical power plant applications. Due to the high densities of dislocations and lath martensite boundaries in G115 steel, interactions between solutes and dislo ...

PERGAMON-ELSEVIER SCIENCE LTD2020

Steel column stability and implications in the seismic assessment of steel structures according to Eurocode 8 Part 3

Dimitrios Lignos, Alexander Riley Hartloper

Seismic performance assessment of new and existing steel structures based on nonlinear static (pushover) analysis necessitates the use of engineering‐oriented models that trace the nonlinear response of structural steel elements under static and cyclic loa ...

2020

Optimum design of low environmental impact structures through component reuse

Jan Friedrich Georg Brütting

Load-bearing systems (structures) in buildings and infrastructure contribute to a significant share of adverse environmental impacts (EI) because of resource- and energy-intensive fabrication. A currently overlooked circular economy strategy to reduce EI i ...

EPFL2020