Publications associées à Long anchorage resistance of reinforcement bars derived from local bond-slip relationships for good and poor bond conditions

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Reuse of cut concrete slabs in new buildings for circular ultra-low-carbon floor designs

Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

The study explores an original idea that responds to the urgent need to reduce the detrimental environmental impacts of load-bearing floor construction in new buildings by reusing saw-cut reinforced concrete (RC) pieces salvaged from soon-to-be demolished ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Maléna Bastien Masse, Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Maléna Bastien Masse, Julie Rachel Devènes, Corentin Jean Dominique Fivet

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Diego Isidoro Heredia Rosa

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

EPFL2024

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

Dimitrios Lignos

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

2023

Reinforcement bond performance in 3D concrete printing: Explainable ensemble learning augmented by deep generative adversarial networks

Xianlin Wang

Integrating various reinforcements into 3D concrete printing (3DCP) is an efficient method to satisfy critical requirements for structural applications. This paper explores an explainable ensemble machine learning (EML) method to predict the bond failure m ...

Elsevier2023

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Geometric tolerances of welded connections with inelastic panel zones

Dimitrios Lignos, Andronikos Skiadopoulos, Ce Wen

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

The General Crack Component Model for reversed cyclic shear

David Michael Volpe Ruggiero

A growing body of research has shown that reversed cyclic shear loading of reinforced concrete (RC) causes effects that are not accounted for in monotonic behavioral models. Notable among these effects are a reduction in shear strength and significant plas ...

2023

Dissipative Embedded Column Bases for Enhanced Seismic Performance of Steel Moment Resisting Frames

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Hiroyuki Inamasu

This paper presents an innovative design concept for embedded column base (ECB) connections. The developed ECB connection achieves a non-degrading hysteretic response. In the proposed ECB connections, the dissipative zone is shifted into the embedded porti ...

EEME2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Cyril Cayron, Roland Logé, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Origin of the enhanced pseudo-elasticity of additively manufactured Fe-17Mn-5Si-4Ni-10Cr-(V, C) shape memory alloy fabricated by laser powder bed fusion

Christian Leinenbach, Irene Ferretto

This study investigated the origin of the enhanced pseudo-elasticity of additively manufactured vanadium carbide-containing Fe-based shape memory alloys. The aged samples with two different starting microstructures, as-built and solution-treated, showed co ...

Elsevier Science Sa2023

Experimental investigation of rotational behavior of pseudo-ductile adhesive angle joints exhibiting variable strain rate

Thomas Keller, Abdolvahid Movahedirad, Ghazaleh Eslami

Pseudo-ductile behavior in composite structural frames can be achieved by enabling their beam-column joints to exhibit nonlinear structural response due to progressive damage, by using pseudo-ductile adhesives. This study investigates the static behavior o ...

2023