Publications associées à Mechanics, Modeling, and Upscaling of Biocemented Soils: A Review of Breakthroughs and Challenges

Publications associées (37)

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

2023

BENIGN LANDSCAPES OF LOW-DIMENSIONAL RELAXATIONS FOR ORTHOGONAL SYNCHRONIZATION ON GENERAL GRAPHS

Nicolas Boumal

Orthogonal group synchronization is the problem of estimating n elements Z(1),& mldr;,Z(n) from the rxr orthogonal group given some relative measurements R-ij approximate to Z(i)Z(j)(-1). The least-squares formulation is nonconvex. To avoid its local minim ...

Siam Publications2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Graph neural networks for dynamic modeling of roller bearings

Olga Fink, Vinay Sharma

Machine learning has paved the way for the real-time monitoring of complex infrastructure and industrial systems. However, purely data-driven methods have not been able to learn the underlying dynamics and generalize them to operating conditions that have ...

PHM Society2023

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Fabio Nobile, Jürg Alexander Schiffmann, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

Amer Soc Mechanical Engineers2023

Interactive design with optimum matchmaking of reused structural elements – a software implementation

Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Jonas Warmuth

Structural systems are a significant contributor to buildings’ embodied carbon and reusing structural elements in new load-bearing applications is one strategy to reduce this impact. However, integrating this approach into existing design workflows without ...

International Association for Shell and Spatial Structures (IASS)2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Herringbone grooved journal bearings (HGJBs) are widely used in micro-turbocompressor applications due to their high load-carrying capacity, low friction, and oil-free solution. However, the performance of these bearings is sensitive to manufacturing devia ...

2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Herringbone grooved journal bearings (HGJBs) are widely used in micro-turbocompressor applications due to their high load-carrying capacity, low friction, and oil-free solution. However, the performance of these bearings is sensitive to manufacturing devia ...

Amer Soc Mechanical Engineers2023

BamX: Rethinking Deployability in Architecture through Weaving

Mark Pauly, Stefana Parascho, Tian Chen, Yingying Ren, Seiichi Eduardo Suzuki Erazo

Deployable gridshells are a class of planar-to-spatial structures that achievea 3D curved geometry by inducing bending on a flat grid of elastic beams. However, theslender nature of these beams often conflicts with the structure’s load-bearing capacity.To ...

De Gruyter2023

An Integrated Approach to Designing Robust Turbocompressors on Gas Bearings Through Surrogate Modeling and Constrained Multi-Objective Optimization

Jürg Alexander Schiffmann, Soheyl Massoudi, Cyril Picard

Designing turbocompressors is a complex and challenging task, as it involves balancing conflicting objectives such as efficiency, stability, and robustness against manufacturing deviations. This paper proposes an integrated design methodology for turbocomp ...

ASME Amer Soc Mechanical Engineers2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

A fully-coupled highly-parallelized geomechanical simulator for assessing induced seismicity

Jean-François Molinari, Brice Tanguy Alphonse Lecampion, Guillaume Anciaux, Nicolas Richart, Emil Gallyamov

Induced seismicity caused by anthropogenic modification of the subsurface effective stress state has been observed in a number of industrial applications -- from hydrocarbon extraction (e.g., Groningen [1]), drilling waste-water disposal (e.g., [2]) to the ...

2023

Utilizing additive manufacturing and mass customization under capacity constraints

Ralf Seifert, Anna Timonina-Farkas, Rachel Agnès Laetitia Rosemonde Marie Lacroix

Additive manufacturing (AM), originally used for prototyping, is increasingly adopted for custom final part production across different industries. However, printing speed and production volume are two barriers for the adoption of AM for product customizat ...

2023

Mechanical performance and upscaling of bio-improved soils

Ray Harran

Ecological awareness, pressing climate considerations and rising need for soil stabilization push forward the quest for alternative solutions in geotechnical engineering such as Microbially Induced Carbonate Precipitation (MICP). Precipitated crystals serv ...

EPFL2022

Mechanical reinforcement of granular hydrogels

Esther Amstad, Alvaro Lino Boris Charlet, Francesca Bono

Granular hydrogels are composed of hydrogel-based microparticles, so-called microgels, that are densely packed to form an ink that can be 3D printed, injected or cast into macroscopic structures. They are frequently used as tissue engineering scaffolds bec ...

ROYAL SOC CHEMISTRY2022

Reinforcing hydrogels with in situ formed amorphous CaCO3

Esther Amstad, Matteo Hirsch, Huachuan Du, Ran Zhao, Michael David Kessler, Tianyu Yuan

Hydrogels are often employed for tissue engineering and moistening applications. However, they are rarely used for load-bearing purposes because of their limited stiffness and the stiffness-toughness compromise inherent to them. By contrast, nature uses hy ...

ROYAL SOC CHEMISTRY2022

Systematic Literature Review of MBSE Tool-Chains

Dimitrios Kyritsis, Jinzhi Lu, Yan Yan

Currently, the fundamental tenets of systems engineering are supported by a model-based approach to minimize risks and avoid design changes in late development stages. The models are used to formalize, analyze, design, optimize, and verify system developme ...

MDPI2022

Re:Crete – reuse of concrete elements in new structures: A footbridge prototype

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Jan Friedrich Georg Brütting, Célia Marine Küpfer, Julie Rachel Devènes

Concrete accounts for the largest share of worldwide building material use and waste generation, with cement production being responsible for approximately 9% of global anthropogenic CO2 emissions. A currently untapped strategy to significantly reduce thes ...

CRC Press2022

Investigation of the effect of mineral dissolution on the geomechanical behaviour of geomaterials

Taeheon Kim

Geotechnical engineering scenarios engaged in internal erosion or mineral dissolution were found worldwide, from CO2 sequestration projects to internal erosion of earth dams. Materials subjected to loss of solid phase from their internal fabric vary from s ...

EPFL2022

Development and Characterization of Rice Husk and Recycled Polypropylene Composite Filaments for 3D Printing

Véronique Michaud

Nowadays the use of natural fiber composites has gained significant interest due to their low density, high availability, and low cost. The present study explores the development of sustainable 3D printing filaments based on rice husk (RH), an agricultural ...

2021