Variant Selection in Fe-20Ni-1.8C under Bending

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (32)

Page 2 sur 2

Drained Clay-Pipe Interface Resistance at Low Normal Stresses and Elevated Temperatures

Roba Houhou

Offshore pipelines that transport hydrocarbons under high pressure and high temperature are usually thermally insulated to maintain an elevated temperature and prevent any heat loss to the surroundings. However, the temperatures at the outer-wall of the pi ...

AMER SOC CIVIL ENGINEERS2023

A fully-coupled highly-parallelized geomechanical simulator for assessing induced seismicity

Jean-François Molinari, Brice Tanguy Alphonse Lecampion, Guillaume Anciaux, Nicolas Richart, Emil Gallyamov

Induced seismicity caused by anthropogenic modification of the subsurface effective stress state has been observed in a number of industrial applications -- from hydrocarbon extraction (e.g., Groningen [1]), drilling waste-water disposal (e.g., [2]) to the ...

2023

Nanomechanical Modeling of the Bending Response of Silicon Nanowires

Yusuf Leblebici, Zuhal Tasdemir

Understanding the mechanical behavior of silicon nanowiresis essentialfor the implementation of advanced nanoscale devices. Although bendingtests are predominantly used for this purpose, their findings shouldbe properly interpreted through modeling. Variou ...

AMER CHEMICAL SOC2023

Frequent asymmetric migrations suppress natural selection in spatially structured populations

Anne-Florence Raphaëlle Bitbol, Alia Abbara

Natural microbial populations often have complex spatial structures. This can impact their evolution, in particular the ability of mutants to take over. While mutant fixation probabilities are known to be unaffected by sufficiently symmetric structures, ev ...

Oxford Univ Press2023

Hydro-mechanichal characterisation of bentonite/steel interfaces

Alessio Ferrari, Eleni Stavropoulou

The hydromechanical response of a Wyoming-type bentonite (MX-80) and its interface with steel was studied in terms of shear resistance under different hydration levels. A series of shear tests under constant normal stress were performed in total suction co ...

2023

Effect of post-heat treatment conditions on shape memory property in 4D printed Fe-17Mn-5Si-10Cr-4Ni shape memory alloy

Christian Leinenbach, Irene Ferretto

The influence of post-heat treatment on the microstructure and properties of 4D printed Fe-17Mn-5Si-10Cr-4Ni (wt. %) shape memory alloy (SMA) produced via a laser powder bed fusion process is investigated in this study. It is shown that heat-treatment temp ...

2022

Persistence of variant selection in red gold alloys

Roland Logé, Cyril Cayron, Margaux Nathalie Dominique Larcher

Recently, a new thermally activated distortion with amplification (TADA) effect has been reported in red gold alloys caused by the A1 -> L1(0) phase transformation. The macroscopic amplification is due to the persistence of variant selection nucleated unde ...

ELSEVIER SCIENCE SA2022

Three-dimensional stress state during dynamic shear rupture propagation along frictional interfaces in elastic plates

Jean-François Molinari, Roozbeh Rezakhani

The state of stress in plates, where one geometric dimensions is much smaller than the others, is often assumed to be of plane stress. This assumption is justified by the fact that the out-of-plane stress components are zero on the free-surfaces of a plate ...

ELSEVIER2022

A Homogenization Model for Soft Magnetic Composites Considering the Effect of Mechanical Stress

Xiaotao Ren

Soft Magnetic Composites (SMC) are an alternative to laminated steels for the design of smaller and lighter electromagnetic devices.Such electromagnetic devices might be subjected to significant mechanical stresses that can alter their electromagnetic prop ...

Institute of Electrical and Electronics Engineers2022

On the behavior of uniaxial static stress loaded micro-scale fused silica beams at room temperature

Yves Bellouard, Christos Edouardos Athanasiou, Saood Ibni Nazir

The question of whether static stress in fused silica relaxes at room temperature is still under debate. Here, we report experimental data investigating the behavior of fused silica at room temperature when subjected to static tensile stress up to 2 GPa st ...

Elsevier2022

Scaling Description of Creep Flow in Amorphous Solids

Matthieu Wyart, Thomas Willem Jan de Geus, Marko Popovic, Wencheng Ji

Amorphous solids such as coffee foam, toothpaste, or mayonnaise display a transient creep flow when a stress E is suddenly imposed. The associated strain rate is commonly found to decay in time as gamma_ -t-nu, followed either by arrest or by a sudden flui ...

AMER PHYSICAL SOC2022

Stress effects on the impedance and ferroelectricity of PVDF-BiFeO3-MWCNT films using xanthan gum as dispersant

Frank Nüesch, Francis Owusu

Composite films based on dispersions of bismuth ferrite (BiFeO3) in polyvinylidene fluoride (PVDF) matrixes were prepared in the presence of multiwalled-carbon-nanotubes (MWCNT), using xanthan gum (XG) as dispersant. Films were prepared by spin coating and ...

ELSEVIER SCIENCE SA2022