Publication

Atomic aluminum content (x) effect on fretting-corrosion of Ti1-xAlxN coatings for orthopedic applications

Publications associées (29)

Elucidating the Rate-Limiting Processes in High-Temperature Sodium-Metal Chloride Batteries

Patrik Schmutz, Corsin Battaglia, Daniel Alexander Landmann

Sodium-metal chloride batteries are considered a sustainable and safe alternative to lithium-ion batteries for large-scale stationary electricity storage, but exhibit disadvantages in rate capability. Several studies identify metal-ion migration through th ...

WILEY2022

Activation of stainless steel 316L anode for anion exchange membrane water electrolysis

Jan Van Herle, Peter Hugh Middleton, Suhas Nuggehalli Sampathkumar, Thomas Benjamin Ferriday

The increased emphasis on renewable energy has resulted in a surge of R&D efforts into hydrogen and battery research. The intensive electrochemical environment surrounding the anodic oxygen evolution reaction (OER) has plagued both the activity and stabili ...

Elsevier2022

Thermophysical and thermomechanical properties of basalt-phenolic FRP rebars under high temperature

Thomas Keller, Hongwei Zhu, Ting Li, Jiahui Shen

An experimental investigation was conducted on the thermophysical and thermomechanical properties of phenolic-basalt fiber-reinforced polymer (P-BFRP) rebars subjected to high temperature. As a comparison, vinylBFRP (V-BFRP) and epoxy-BFRP (E-BFRP) rebars ...

ELSEVIER SCI LTD2022

A Crevice Corrosion Model for Biomedical Trunnion Geometries and Surfaces Feature

Stefano Mischler, Anna Neus Igual Muñoz, Angela Bermudez Castañeda

Modular hip joint implants were introduced in arthroplasty medical procedures because they facilitate the tailoring of patients’ anatomy, the use of different materials in one single configuration, as well as medical revision. However, in certain cases, su ...

2021

Modeling Current Transients in a Reciprocal Motion Tribocorrosion Experiment

Stefano Mischler, Anna Neus Igual Muñoz, Shoufan Cao

Tribocorrosion of passivating metals is a dynamic phenomenon causing degradation of materials by a combination of mechanical wear and electrochemical dissolution. The mechanical action typically produces a local removal of particles, metal as well as oxide ...

ELECTROCHEMICAL SOC INC2021

A comparative surface analysis of explanted hip joint prostheses made of different biomedical alloys

Stefano Mischler, Angela Bermudez Castañeda, Adriana Esguerra Arce, Johanna Esguerra Arce

The introduction of modular design in total hip arthroplasty has enabled the use of different materials in one single configuration and the adjustment of the prosthesis to the patient's body, and facilitated medical revisions. However, modularity leads to ...

IMPRENTA UNIV ANTIOQUIA2021

A lubricated tribocorrosion model incorporating surface roughness

Stefano Mischler, Shoufan Cao

This study presents an improvement of an existing tribocorrosion model developed for passive CoCrMo alloys. This model is based on an empirical formalism established by Duncan Dowson in his pioneering works on the relation between wear and elasto-hydrodyna ...

2021

Adhesive wear regimes on rough surfaces and interaction of micro-contacts

Jean-François Molinari, Son-Jonathan Pham-Ba

We develop an analytical model of adhesive wear between two unlubricated rough surfaces, forming micro-contacts under normal load. The model is based on an energy balance and a crack initiation criteria. We apply the model to the problem of self-affine rou ...

2021

The ratio of shear to elastic modulus of in-plane loaded masonry (vol 53, 40, 2020)

Katrin Beyer, Bastian Valentin Wilding, Michele Godio

A correction to this paper has been published: https://doi.org/10.1617/s11527-021-01653-6 ...

SPRINGER2021