Publications associées à Effects of Ni additions, trace elements and solidification kinetics on microstructure formation in Sn-0.7Cu solder

Publications associées (31)

Composition and Element Distribution Mapping of γ′ and γ" Phases of Inconel 718 by High-Resolution Scanning Transmission Electron Microscopy and X-ray Energy-Dispersive Spectrometry

The main strengthening mechanism for Inconel 718 (IN718), a Ni-based superalloy, is precipitation hardening by gamma ' and gamma '' particles. It is thus essential, for good alloy performance, that precipitates with the desired chemical composition have ad ...

MDPI2024

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials Part-III: Experimental verification of conversion products and infiltration depth by infiltration of Si-Zr alloy into mixed SiC/ graphite preforms

Ludger Weber, Caroline Hain, Manoj Kondibhau Naikade, Annapaola Parrilli

Porous carbonaceous preforms, made from graphite and silicon carbide (SiC) powders, with varying graphite powder mass fractions and particle sizes, were infiltrated at 1500 degrees C and 1700 degrees C by Si-8 at. pct Zr alloy to produce dense Si-Zr-SiC co ...

ELSEVIER SCI LTD2023

Control of intermetallics in the interface in directed energy deposition of titanium on stainless steel 316L

Di Cui

Application of a single metal or alloy is often restricted by its properties from optimal combination of performance and cost. Therefore, there is a vast need of joining dissimilar metals for various applications in biomedical, aerospace, automobile and ma ...

EPFL2023

Crystalline or amorphous? A critical evaluation of phenomenological phase selection rules

Johann Michler, Caroline Hain

In this work, we reviewed the available phase selection rules comprising atomic size and topological aspects, entropies, enthalpies, melting points, valence and itinerant electron concentrations, as well as electronegativity, and validated them using a car ...

ELSEVIER SCI LTD2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

Origin of the enhanced pseudo-elasticity of additively manufactured Fe-17Mn-5Si-4Ni-10Cr-(V, C) shape memory alloy fabricated by laser powder bed fusion

Christian Leinenbach, Irene Ferretto

This study investigated the origin of the enhanced pseudo-elasticity of additively manufactured vanadium carbide-containing Fe-based shape memory alloys. The aged samples with two different starting microstructures, as-built and solution-treated, showed co ...

Elsevier Science Sa2023

Modelling of metal alloys in realistic conditions with machine learning

Nataliya Lopanitsyna

Computer simulations based on statistical methods have emerged as a powerful tool for studying structure-property relationships at the atomistic level. However, to provide reliable insights into materials in realistic conditions, it is essential to accurat ...

EPFL2023

Phase and microstructure selection in peritectic alloys under high G-V ratio

Wilfried Kurz

A new model for the case of a superposition of a phase transformation and a microstructure transition from columnar plane front to equiaxed dendritic growth for peritectic alloys is presented. This model is applied to Fe-Ni alloys where a phase transition ...

WALTER DE GRUYTER GMBH2022

Machine learning for metallurgy IV: A neural network potential for Al-Cu-Mg and Al-Cu-Mg-Zn

William Curtin, Daniel John Gilles Marchand

Most metallurgical properties, e.g., dislocation propagation, precipitate formation, can only be fully understood atomistically but most phenomena and quantities of interest cannot be measured experimentally. Accurate simulation methods are essential but f ...

2022

A Low-Temperature Annealing Method for Alloy Nanostructures and Metasurfaces: Unlocking a Novel Degree of Freedom

Olivier Martin, Christian Santschi, Hsiang-Chu Wang, Jeonghyeon Kim, Debdatta Ray

The material and exact shape of a nanostructure determine its optical response, which is especially strong for plasmonic metals. Unfortunately, only a few plasmonic metals are available, which limits the spectral range where these strong optical effects ca ...

Wiley-V C H Verlag Gmbh2022

Processability, microstructure and precipitation of a Zr-modified 2618 aluminium alloy fabricated by laser powder bed fusion

Christian Leinenbach, Xavier Maeder

Additive manufacturing offers the opportunity to produce complex geometries from novel alloys with improved properties. Adapting conventional alloys to the process-specific properties can facilitate rapid implementation of these materials in industrial pra ...

2022

Development of High-Strength Aluminum Alloys for Additive Manufacturing

Marvin Lennard Schuster

Metal additive manufacturing (AM) offers the possibility to rapidly produce complex geometries that are not achievable with conventional manufacturing methods. The two most common technologies, Laser Powder Bed Fusion (LPBF) and Direct Metal Deposition (DM ...

EPFL2022

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

Roland Logé, Cyril Cayron, Baptiste Thomas Jean Rouxel

Cu-Be alloys provide excellent electrical and mechanical properties, but present serious health hazards during manufacturing. Among alternative alloys, the Cu-Ti system has the highest yield strength; however, Ti cannot be easily solutionized at concentrat ...

ELSEVIER SCI LTD2022

Peritectic equilibrium in Fe-Co alloys

Wilfried Kurz

Recent results of directional solidification experiments with Fe-Co alloys were not consistent with the presently accepted peritectic phase diagram. Therefore, the Fe-rich part of this phase diagram was re-examined. High-temperature gradient plane front so ...

WALTER DE GRUYTER GMBH2022

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials. Part II: Experimental verification of modelling approaches by infiltration of Si-Zr alloy into idealized microchannels

Ludger Weber, Caroline Hain, Manoj Kondibhau Naikade

In this work, the mechanisms leading to the pore closure in reactive melt infiltration (RMI) of carbon by pure silicon and a near eutectic Si-8 at-pct Zr alloy at 1500 and 1700 degrees C under vacuum were studied. Various geometrical configurations of micr ...

ELSEVIER SCI LTD2022

Screw vs. edge dislocation strengthening in body-centered-cubic high entrophy alloys and implications for guided alloy design

William Curtin, Francesco Maresca, Carolina Baruffi

Body-centered-cubic (BCC) high entropy alloys (HEAs) can show exceptionally high strength up to high temperatures. Mechanistic theories are needed to guide alloy discovery within the immense multicomponent HEA compositional space. Here, two new theories fo ...

SPRINGER HEIDELBERG2022

Persistence of variant selection in red gold alloys

Roland Logé, Cyril Cayron, Margaux Nathalie Dominique Larcher

Recently, a new thermally activated distortion with amplification (TADA) effect has been reported in red gold alloys caused by the A1 -> L1(0) phase transformation. The macroscopic amplification is due to the persistence of variant selection nucleated unde ...

ELSEVIER SCIENCE SA2022

A ductility criterion for bcc high entropy alloys

William Curtin, Binglun Yin, Eleanor Yi Kei Mak

A current goal driving alloy development is the identification of alloy compositions for high temperature applications but with the additional requirement of sufficient ductility at ambient temperatures. Multicomponent, single-phase, polycrystalline High E ...

PERGAMON-ELSEVIER SCIENCE LTD2021

Surface energy contributions to the work of infiltration in metal matrix composite processing

Andreas Mortensen, Gionata Schneider

The work needed to mechanically drive molten metal into a porous solid preform when producing a composite material by infiltration can significantly exceed the energy change required for thermodynamically reversible infiltration. We measure, by quantitativ ...

2021

Giant hardening response in AlMgZn(Cu) alloys

William Curtin, Daniel John Gilles Marchand

This study presents a thermomechanical processing concept which is capable of exploiting the full industrial application potential of recently introduced AlMgZn(Cu) alloys. The beneficial linkage of alloy design and processing allows not only to satisfy th ...

PERGAMON-ELSEVIER SCIENCE LTD2021