Publications associées à Curvature of micropores in Al-Cu alloys: An X-ray tomography study

Publications associées (30)

Impact of CO2-rich seawater injection on the flow properties of basalts

Cesare Griner, Lyesse Laloui, Eleni Stavropoulou

Permanent CO storage in basalts through mineralisation offers a promising solution for reducing carbon emissions and mitigating climate change. This study focuses on the impact of potential mineralisation on the flow properties of the basaltic material. Fl ...

2024

DTT toroidal field conductor samples test in Sultan: DC and AC characterization

Kamil Sedlák, Mattia Ortino, Hugues Marie Alain Bajas

The superconducting magnet system of the Divertor Tokamak Test (DTT) facility, composed of 18 toroidal field (TF) coils, 6 poloidal field coils and a central solenoid, has been designed and many procurements have been launched. Some manufacturing aspects a ...

Iop Publishing Ltd2024

Flash Melting Amorphous Ice

Marcel Drabbels, Ulrich Lorenz, Gabriele Bongiovanni, Constantin Richard Krüger, Nathan Junior Mowry

Water can be vitrified if it is cooled at high rates, which makes it possible to outrun crystallization in so-called no man’s land, a range of deeply supercooled temperatures where water crystallizes rapidly. Here, we study the reverse process in pure wate ...

2024

Effect of wettability and textile architecture on fluid displacement and pore formation during infiltration of carbon fibrous preforms

Véronique Michaud, Baris Çaglar, Helena Luisa Teixido Pedarros

We seek to address how air entrapment mechanisms during infiltration are influenced by the wetting characteristics of the fluid and the pore network formed by the reinforcement. To this end, we evaluated the behavior of two model fluids with different surf ...

Elsevier Sci Ltd2023

3-D contact and pore network analysis of MICP cemented sands

Dimitrios Terzis

The study describes a comprehensive methodology to evaluate X-Ray micro-computed tomography data from sand samples and to characterize their 3D microstructural properties. Fine and medium-grained sands are analyzed in their natural and bio-cemented states. ...

SPRINGER2023

Unsupervised Electrofacies Clustering Based on Parameterization of Petrophysical Properties: A Dynamic Programming Approach

François Fleuret

Electrofacies using well logs play a vital role in reservoir characterization. Often, they are sorted into clusters according to the self-similarity of input logs and do not capture the known underlying physical process. In this paper, we propose an unsupe ...

SOC PETROPHYSICISTS & WELL LOG ANALYSTS-SPWLA2023

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials. Part II: Experimental verification of modelling approaches by infiltration of Si-Zr alloy into idealized microchannels

Ludger Weber, Caroline Hain, Manoj Kondibhau Naikade

In this work, the mechanisms leading to the pore closure in reactive melt infiltration (RMI) of carbon by pure silicon and a near eutectic Si-8 at-pct Zr alloy at 1500 and 1700 degrees C under vacuum were studied. Various geometrical configurations of micr ...

ELSEVIER SCI LTD2022

Cross verified independent measurements of correlated bubble property distributions as part of the scale-up of a catalytic bubbling fluidized bed reactor

Philipp Fedor Riechmann

Methanation can be applied as part of a Power-to-Gas (PtG) concept to store renewable electricity. Using a catalytic bubbling fluidized bed (BFB) methanation reactor allows a flexible and economic operation. Properties of bubbles rising through the fluidiz ...

EPFL2022

Exploring the inner workings of the clove hitch knot

Pedro Miguel Nunes Pereira de Almeida Reis, Tomohiko Sano, Paul Johanns, Paul Grandgeorge

We perform a combined experimental and computational investigation of the clove hitch knot. We develop a physical model for the clove hitch by tying an elastic rod onto a rigid cylinder. In the experiments, we characterize the mechanical performance, geome ...

ELSEVIER2022

Insights into the interaction of a shale with CO2

Lyesse Laloui, Eleni Stavropoulou

Caprock formations, such as shales, play a key role in safe underground CO2 storage since they serve as a hydromechanical barrier that prevents migration of the injected CO2 to the surface. While their hydromechanical response is important to ensure their ...

2022

Medipix4, a high granularity four sides buttable pixel readout chip for high resolution spectroscopic X-ray imaging at rates compatible with medical CT scans

Viros Sriskaran

Medipix4 is the latest member in the Medipix/Timepix family of pixel detector chips aimed at high rate spectroscopic X-ray imaging using high-Z materials. The chip address the limitations of conventional hybrid pixel detectors for X-ray imaging. Its predec ...

EPFL2022

Machine learning for metallurgy IV: A neural network potential for Al-Cu-Mg and Al-Cu-Mg-Zn

William Curtin, Daniel John Gilles Marchand

Most metallurgical properties, e.g., dislocation propagation, precipitate formation, can only be fully understood atomistically but most phenomena and quantities of interest cannot be measured experimentally. Accurate simulation methods are essential but f ...

2022

Development of High-Strength Aluminum Alloys for Additive Manufacturing

Marvin Lennard Schuster

Metal additive manufacturing (AM) offers the possibility to rapidly produce complex geometries that are not achievable with conventional manufacturing methods. The two most common technologies, Laser Powder Bed Fusion (LPBF) and Direct Metal Deposition (DM ...

EPFL2022

Learning to sample in Cartesian MRI

Thomas Sanchez

Magnetic Resonance Imaging (MRI) is a non-invasive, non-ionizing imaging modality with unmatched soft tissue contrast. However, compared to imaging methods like X-ray radiography, MRI suffers from long scanning times, due to its inherently sequential acqui ...

EPFL2022

Bragg edge tomography characterization of additively manufactured 316L steel

Roland Logé, Christian Leinenbach, Nikola Kalentics

In this work we perform a neutron Bragg edge tomography of stainless steel 316L additive manufacturing samples, one as built via standard laser powder bed fusion, and one using the novel three-dimensional (3D) laser shock peening technique. First, we consi ...

AMER PHYSICAL SOC2022

Three-Dimensional Cubic Barcodes

Martin Vetterli, Adam James Scholefield, Golnooshsadat Elhami

We consider three-dimensional cubic barcodes, consisting of smaller cubes, each built from one of two possible materials and carry one bit of information. To retrieve the information stored in the barcode, we measure a 2-D projection of the barcode using a ...

2022

Multiphase transport and evaporative cooling in fuel cell gas diffusion layers

Sarah van Rooij

The use of evaporative cooling in the gas diffusion layer (GDL) of polymer electrolyte fuel cells has been proposed as a simple yet impactful solution to simultaneously provide the functionality of cell cooling, thanks to the dissipation of the latent heat ...

EPFL2021

A ductility criterion for bcc high entropy alloys

William Curtin, Binglun Yin, Eleanor Yi Kei Mak

A current goal driving alloy development is the identification of alloy compositions for high temperature applications but with the additional requirement of sufficient ductility at ambient temperatures. Multicomponent, single-phase, polycrystalline High E ...

PERGAMON-ELSEVIER SCIENCE LTD2021

Critical crystallization properties of an industrial-grade Zr-based metallic glass used in additive manufacturing

Roland Logé, Jamasp Jhabvala, Navid Sohrabi

The major challenge to overcome when processing metallic glasses (MGs) is to avoid crystallization. Therefore, time-temperature-transformation (TTT) diagrams are used, but they are often derived from experiments in which heating or cooling rates are limite ...

2021

Operando X-ray diffraction during laser 3D printing: from machine design to experiments and computer simulations

Samy Hocine

The importance of additive manufacturing, also known as 3D printing, has grown exponentially in the recent years thanks to its high flexibility to manufacture intricate parts. This process can be divided into many different sub-categories, depending on the ...

EPFL2020