Publication

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Publications associées (29)

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Maléna Bastien Masse, Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

Rubble stone masonry is a common construction typology of historical city centres and vernacular architecture. While past earthquakes have shown that it is one of the most vulnerable masonry construction typologies, there are few experimental campaigns giv ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Reuse of cut concrete slabs in new buildings for circular ultra-low-carbon floor designs

Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

The study explores an original idea that responds to the urgent need to reduce the detrimental environmental impacts of load-bearing floor construction in new buildings by reusing saw-cut reinforced concrete (RC) pieces salvaged from soon-to-be demolished ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Reducing uncertainties in response predictions of earthquake-damaged masonry buildings using data from image-based inspection

Ian Smith, Katrin Beyer, Bryan German Pantoja Rosero, Mathias Christian Haindl Carvallo

Image information about the state of a building after an earthquake, which can be collected without endangering the post-earthquake reconnaissance activities, can be used to reduce uncertainties in response predictions for future seismic events. This paper ...

Springer2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Maléna Bastien Masse, Julie Rachel Devènes, Corentin Jean Dominique Fivet

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Full Scale Experiments of a Composite Steel Moment Resisting Frame: Behavioral Insights and Implications on Seismic Design

Dimitrios Lignos, Hammad El Jisr

This paper discusses the cyclic performance of a heavily instrumented 2-bay full-scale composite-steel moment resisting frame (CMRF) sub-system from the onset of structural damage up until incipient collapse. The CMRF featured stiffened end plate bolted co ...

EEME2023

Full-Scale Experiments of Cyclically Loaded Welded Moment Connections with Highly Dissipative Panel Zones and Simplified Weld Details

Dimitrios Lignos, Andronikos Skiadopoulos

This paper presents the experimental results of two welded unreinforced flange-welded web (WUF-W) beam-to-column connections that defy the current design paradigm of prequalified welded connections. The proposed WUF-W connections feature customized beveled ...

2023

Geometric tolerances of welded connections with inelastic panel zones

Dimitrios Lignos, Andronikos Skiadopoulos, Ce Wen

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

Dimitrios Lignos

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

2023

Towards instability-free welded moment connections

Dimitrios Lignos, Andronikos Skiadopoulos

In capacity-designed steel moment resisting frames (MRFs), inelastic deformations are mostly concentrated in the steel beams and the column fixed ends of the first story, while the participation of the panel zones in energy dissipation is limited. In such ...

2023

Dissipative Embedded Column Bases for Enhanced Seismic Performance of Steel Moment Resisting Frames

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Hiroyuki Inamasu

This paper presents an innovative design concept for embedded column base (ECB) connections. The developed ECB connection achieves a non-degrading hysteretic response. In the proposed ECB connections, the dissipative zone is shifted into the embedded porti ...

EEME2023

Digital-Image-Correlation for Simulating Cyclic Local Buckling in Steel Beams

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Selimcan Ozden

Nonlinear continuum finite element (CFE) analyses rely on accurate multiaxial constitutive law formulations along with reliable imperfection patterns for simulating nonlinear geometric instabilities in steel members under mechanical loading. Validations of ...

Wiley2023