Publications associées à Diffuse light transmittance of glass fiber-reinforced polymer laminates for multifunctional load-bearing structures

Publications associées (29)

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Additive Manufacturing of Bioinspired Mineral-Based Composites

Ran Zhao

Biominerals are used by natural organisms for example as structural supports and optical sensors. They are produced from a limited number of elements and under ambient conditions. Nevertheless, they often possess excellent mechanical properties and sometim ...

EPFL2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

On the influence of flow-front orientation on stringer stiffened composite panels in water impacts

Véronique Michaud

Water impacts form the critical load case for high-performance carbon fibre reinforced polymer (CFRP) racing craft. Such events produce a peaked, non-uniform pressure distribution that travels along a hull panel as it is immersed. Current design standards ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Quench Detection and Temperature Measurement With Fiber Optic Sensors

Davide Uglietti, Kamil Sedlák

For the EU DEMO conductor testing, a temperature sensor based on Fiber Bragg Grating (FBG) optical fiber is studied at the EPFL Swiss Plasma Center. The SULTAN test facility has been upgraded to use fiber optic sensor for temperature monitoring and quench ...

IEEE Institute of Electrical and Electronics Engineers2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

In-Sensor Passive Speech Classification with Phononic Metamaterials

Luis Guillermo Villanueva Torrijo, Daniel Moreno Garcia

Mitigating the energy requirements of artificial intelligence requires novel physical substrates for computation. Phononic metamaterials have vanishingly low power dissipation and hence are a prime candidate for green, always-on computers. However, their u ...

Wiley-V C H Verlag Gmbh2024

An explorative method to support design decisions based on carbon constraints and daylight sufficiency needs

Nazanin Rezaei Oghazi

The global construction industry contributes to 37% of carbon emissions associated to both building operations and construction. To help achieve the net-zero targets set by 2050, it is mandated to achieve a 50% reduction in carbon emissions by 2030. As we ...

EPFL2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

Investigation of mycelium film as the adhesive for poplar veneer bonding: insight into interfacial bonding mechanisms

Wenjing Sun

The emergence of mycelium-bonded biocomposites has been stimulated in the quest for sustainable development. These biocomposites exhibit enhanced mechanical properties through hot pressing, with mycelium playing a crucial role as both the adhesive and rein ...

Taylor & Francis Ltd2024

Experimental characterization and stochastic models for time-dependent rupture of thin-ply composite laminates

Kanthasamy Ubamanyu

Thin-laminate composites with thicknesses below 200 mu m hold significant promise for future, larger, and lighter deployable structures. This paper presents a study of the time-dependent failure behavior of thin carbon-fiber laminates under bending, focusi ...

2024

Electrical and Optical Manifestations of Flat Band Physics in Van der Waals Materials

Gabriele Pasquale

The scientific progress is significantly transforming contemporary society with the introduction and widespread application of technologies like artificial intelligence and quantum computing. Despite their profound impact, these technologies necessitate en ...

EPFL2024

Filiform Variable Stiffness Technologies for Medical Robotics

Yegor Piskarev

In recent years, soft robotics has surged in applications like wearables, drones, smart fabrics, and medical instruments. Due to their compliance, these devices excel in tasks demanding dexterity and adaptability, such as manipulation, locomotion, crash re ...

EPFL2024

Exploring High-Performance and Energy-Efficient Architectures for Edge AI-Enabled Applications

Joshua Alexander Harrison Klein

The desire and ability to place AI-enabled applications on the edge has grown significantly in recent years. However, the compute-, area-, and power-constrained nature of edge devices are stressed by the needs of the AI-enabled applications, due to a gener ...

EPFL2024

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

Solar-assisted clean steam generator, a cleaner production approach for sustainable healthcare facilities

Mohammad Jamshidmofid, Fernando Porté Agel

Healthcare sector buildings, particularly hospitals, significantly contribute to global energy consumption and greenhouse gas emissions. Hospitals require a substantial amount of steam, including the essential hygienic or " clean steam, " that is currently ...

Elsevier Sci Ltd2024

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Strategies for energy-efficient frontal polymerisation processing and microstructural evaluation of fibre reinforced composites

Jacobus Gerardus Rudolph Staal

Liquid composite moulding methods are widely applied for manufacturing of fibre reinforced polymer (FRP) composites and consist of two main stages: impregnation of fibrous reinforcements by a liquid monomer resin and curing of this resin. This thesis work ...

EPFL2023