Publications associées à Dissipative Embedded Column Bases for Enhanced Seismic Performance of Steel Moment Resisting Frames

Publications associées (32)

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

EPFL2024

Seismic Performance of Steel Moment-Resisting Frames Utilizing Dissipative Embedded Column Base Connections

Dimitrios Lignos, Nenad Bijelic

Experimental and numerical studies on steel wide-flange columns as part of steel moment-resisting frames (MRFs) revealed that their seismic performance can be compromised when seismically compact, yet relatively slender cross sections are adopted. One aspe ...

Springer Science and Business Media Deutschland GmbH2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Reuse of cut concrete slabs in new buildings for circular ultra-low-carbon floor designs

Corentin Jean Dominique Fivet, Numa Joy Bertola, Célia Marine Küpfer

The study explores an original idea that responds to the urgent need to reduce the detrimental environmental impacts of load-bearing floor construction in new buildings by reusing saw-cut reinforced concrete (RC) pieces salvaged from soon-to-be demolished ...

2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

Rubble stone masonry is a common construction typology of historical city centres and vernacular architecture. While past earthquakes have shown that it is one of the most vulnerable masonry construction typologies, there are few experimental campaigns giv ...

2024

Full-Scale Experiments of Cyclically Loaded Welded Moment Connections with Highly Dissipative Panel Zones and Simplified Weld Details

Dimitrios Lignos, Andronikos Skiadopoulos

This paper presents the experimental results of two welded unreinforced flange-welded web (WUF-W) beam-to-column connections that defy the current design paradigm of prequalified welded connections. The proposed WUF-W connections feature customized beveled ...

2023

Full Scale Experiments of a Composite Steel Moment Resisting Frame: Behavioral Insights and Implications on Seismic Design

Dimitrios Lignos, Hammad El Jisr

This paper discusses the cyclic performance of a heavily instrumented 2-bay full-scale composite-steel moment resisting frame (CMRF) sub-system from the onset of structural damage up until incipient collapse. The CMRF featured stiffened end plate bolted co ...

EEME2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Geometric tolerances of welded connections with inelastic panel zones

Ce Wen, Dimitrios Lignos, Andronikos Skiadopoulos

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

Towards instability-free welded moment connections

Dimitrios Lignos, Andronikos Skiadopoulos

In capacity-designed steel moment resisting frames (MRFs), inelastic deformations are mostly concentrated in the steel beams and the column fixed ends of the first story, while the participation of the panel zones in energy dissipation is limited. In such ...

2023