Publications associées à Assessing continuum plasticity postulates with grain stress and local strain measurements in triaxially compressed sand

Publications associées (13)

Computational Imaging: a Multi-Facet Perspective

Computational Imaging (CI) is the field concerned with reconstructing images of some quantity of interest from a finite number of measurements. It is pervasive in science and engineering problems by enabling the reconstruction of images from a variety of m ...

EPFL2025

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Archimedean Oath: A reflection tool for responsible engineers

Ingrid Le Duc, Vittorio Rossi

This workshop, inspired by the Archimedean Oath, seeks to engage participants in critically reflecting on the responsibilities of engineers in society. Following the update of the content of the Oath to address contemporary challenges, the workshop aims at ...

European Society for Engineering Education (SEFI)2024

Simultaneous strength and ductility enhancement of wire-arc directed energy deposited Al-Cu alloy by interlayer laser shock peening

Ke Huang, Yandong Jing

Wire-arc directed energy deposition (wire-arc DED), recognized for its ability to produce large-scale parts, has gained considerable attention. However, a critical issue with this method is the high prevalence of internal porosity defects found in the manu ...

Elsevier Science Sa2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

Extension of the OFFBEAT fuel performance code to finite strains and validation against LOCA experiments

Andreas Pautz, Alessandro Scolaro, Carlo Fiorina, Edoardo Luciano Brunetto

The mechanical analysis of nuclear fuel behavior under base-irradiation conditions has traditionally been performed adopting the small-strain approximation. However, many cases of interest for fuel behavior involve the occurrence of large rod deformations ...

ELSEVIER SCIENCE SA2023

Improving the Accuracy of Fracture Toughness Measurement in Burst Experiments

Guanyi Lu

Experimental studies suggest that the fracture toughness of rocks increases with the confining pressure. Among many methods to quantify this dependency, a so-called burst experiment (Abou-Sayed, 1978) may be the most widely applied in practice. Its thick w ...

SPRINGER WIEN2022

Design and modelling of a tubular dielectric elastomer actuator with constrained radial displacement as a cardiac assist device

Yves Perriard, Yoan René Cyrille Civet, Jonathan André Jean-Marie Chavanne, Armando Matthieu Walter

In this paper, we propose an improvement of a dielectric elastomer actuator (DEA) based augmented aorta. The actuator is a multi-layered tubular DEA subject to the internal pressure of the blood. When activated in synchronisation with the heart, the DEA su ...

IOP PUBLISHING LTD2021

A conveyor belt experimental setup to study the internal dynamics of granular avalanches

Christophe Ancey, Tomás Alfredo Trewhela Palacios

This paper shows how a conveyor belt setup can be used to study the dynamics of stationary granular flows. To visualise the flow within the granular bulk and, in particular, determine its composition and the velocity field, we used the refractive index mat ...

SPRINGER2021

Static and Fatigue Biaxial Flexural Behavior of Strain-Hardening UHPFRC Thin Slab Elements

Xiujiang Shen

Cast-in-place thin layers of Ultra-High Performance Fiber Reinforced Cementitious Composites (UHPFRC) on the specific zones of existing reinforced concrete (RC) bridge decks has been demonstrated to be a technically efficient and economic rehabilitation an ...

EPFL2020

Length Microstructure analysis of epitaxial BaTiO3 thin films on SrTiO3-buffered Si: Strain and dislocation density quantification using HRXRD methods

Patrik Willi Hoffmann, Wojciech Bozydar Szmyt

Barium titanate (BTO) is a promising perovskite-like material, exhibiting interesting functionalities, such as ferroelectricity, piezoelectricity, high dielectric constant, and electrooptic coefficients. All these properties are closely related to the orie ...

2020

Solid-state to solution helicity inversion of pseudotetrahedral chiral copper(II) complexes with 2,4-dihalo-salicylaldiminate ligands

Rosario Scopelliti

The enantiopure Schiff bases (R or S)-N-1-( phenyl)ethyl-2,4-X-1,X2(-)salicylaldimine (X-1, X-2 = Cl, Br, I) coordinate to copper(II) and provide pseudotetrahedral bis[(S or R)-N-1-(phenyl)ethyl-(2,4-X-1,X-2-salicylaldiminato.2N,O)]-./.-Cu(II) (kappa N-2,O ...

ROYAL SOC CHEMISTRY2020

First-principles-based prediction of yield strength in the RhIrPdPtNiCu high-entropy alloy

William Curtin, Binglun Yin

High-entropy alloys are random alloys with five or more components, often near equi-composition, that often exhibit excellent mechanical properties. Guiding the design of new materials across the wide composition space requires an ability to compute necess ...

2019