Publications associées à Piecewise non-linear constant life diagram formulation for FRP composite materials

Publications associées (29)

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Single-Well Pore Pressure Preconditioning for Enhanced Geothermal System Stimulation

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Mathias Alexandre David Lebihain

The stress state is an important parameter in terms of both earthquake nucleation and rupture. Here, a new stimulation technique is proposed for Enhanced Geothermal Systems (EGSs), which have previously been burdened with a number of high-profile incidence ...

2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Probabilistic fatigue model for composites based on the statistical characteristics of the cycles to failure

Anastasios Vassilopoulos

A probabilistic model for estimating the fatigue life of composite laminates based on the mean value and standard deviation of the fatigue life is introduced here for predicting the distribution of fatigue life at any stress level for a constant stress rat ...

ELSEVIER SCI LTD2022

Three-dimensional stress state during dynamic shear rupture propagation along frictional interfaces in elastic plates

Jean-François Molinari, Roozbeh Rezakhani

The state of stress in plates, where one geometric dimensions is much smaller than the others, is often assumed to be of plane stress. This assumption is justified by the fact that the out-of-plane stress components are zero on the free-surfaces of a plate ...

ELSEVIER2022

A Novel Method to Quantify Self-Healing Capabilities of Fiber-Reinforced Polymers

Cecilia Scazzoli, Véronique Michaud, Amaël Maximilien Cohades, Robin Samuel Trigueira

The present work investigates a novel and practical method to evaluate the healing efficiency of carbon-reinforced polymer composites. The method should be representative of damage occurring during the lifetime of a composite part, should tend to damage th ...

FRONTIERS MEDIA SA2022

Experimental quantification of 3D deformations in sensitive clay during stress-probing

Edward Carlo Giorgio Andò

Unique four-dimensional (4D) deformation data are collected during drained triaxial tests on intact specimens of a natural sensitive clay. This requires the development of a miniature triaxial cell for advanced stress path testing, specifically designed fo ...

ICE PUBLISHING2022

Crack propagation in CFRP laminates under mode I monotonic and fatigue loads: A methodological study

John Botsis, Georgios Pappas, Charlie Joseph Simon Blondeau

Delamination in composite materials is often accompanied by fiber bridging that increases resistance to crack growth. Here, delamination of two unidirectional carbon/epoxy systems was studied under monotonic and displacement-controlled fatigue loading. One ...

ELSEVIER SCI LTD2021

Origami-inspired carbon fiber-reinforced composite sandwich materials - Fabrication and mechanical behavior

Thomas Keller

A folding fabrication method inspired by origami for carbon fiber-reinforced composites to fabricate three-dimensional structures is presented. PMI foams serve as substrates, making it possible to manufacture this kind of origami-inspired composite sandwic ...

ELSEVIER SCI LTD2021

The influence of the kinematics of rough surface engagement on the transfer of forces in cracked concrete

Miguel Fernández Ruiz

One of the most instrumental aspects governing the response of structural concrete at ultimate limit state refers to the possibility of developing smeared cracking patterns within a member (associated normally to the presence of sufficient reinforcement fo ...

2021

Fatigue of reinforced UHPFRC members and monitoring of fatigue action effects on bridges

Bartlomiej Wojciech Sawicki

The objective of this thesis is to develop knowledge and methods to prevent fatigue failure of bridges. The Fatigue Limit State is investigated from both the demand (S) and resistance (R) side. The S-part focuses on reduction of uncertainties through monit ...

EPFL2021

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials

Thomas Keller, Ghazaleh Eslami

This paper introduces a new fatigue life prediction methodology for viscoelastic materials in the tension-tension fatigue loading region. The model was established based on the total amount of energy dissipated during fatigue loading, and offers two main a ...

ELSEVIER SCI LTD2021

Numerical modeling of two-dimensional delamination growth in composite laminates with in-plane isotropy

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

The two-dimensional (2D) delamination growth in fiber-reinforced polymer (FRP) laminates with in-plane isotropy under Mode I loading condition was numerically investigated using finite element analyses. Two sizes of plate models were developed, focusing on ...

2021

Flexural behaviour of post-tensioned glass beams: Experimental and analytical study of three beam typologies

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

The concept of post-tensioned glass beams builds on the concrete analogy of the reinforced glass beams. By additionally prestressing the reinforcement in a post-tensioned system, a compressive pre-stress is applied on the glass, enhancing the initial fract ...

2021