Publication

Comparative Evaluation of Foil Bearings with Different Compliant Structures for Improved Manufacturability

Publications associées (30)

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

EPFL2023

Triple Crossed Flexure Pivot Based on a Zero Parasitic Center Shift Kinematic Design

Simon Nessim Henein, Etienne Frédéric Gabriel Thalmann

Thanks to their absence of play, absence of contact friction and possible monolithic fabrication, flexure pivots offer advantages over traditional bearings in small-scale, high accuracy applications and environments where lubrication and wear debris are pr ...

2022

Mechanical reinforcement of granular hydrogels

Alvaro Lino Boris Charlet, Esther Amstad, Francesca Bono

Granular hydrogels are composed of hydrogel-based microparticles, so-called microgels, that are densely packed to form an ink that can be 3D printed, injected or cast into macroscopic structures. They are frequently used as tissue engineering scaffolds bec ...

ROYAL SOC CHEMISTRY2022

Reinforcing hydrogels with in situ formed amorphous CaCO3

Michael David Kessler, Huachuan Du, Esther Amstad, Matteo Hirsch, Ran Zhao, Tianyu Yuan

Hydrogels are often employed for tissue engineering and moistening applications. However, they are rarely used for load-bearing purposes because of their limited stiffness and the stiffness-toughness compromise inherent to them. By contrast, nature uses hy ...

ROYAL SOC CHEMISTRY2022

Re:Crete – reuse of concrete elements in new structures: A footbridge prototype

Maléna Bastien Masse, Célia Marine Küpfer, Julie Rachel Devènes, Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting

Concrete accounts for the largest share of worldwide building material use and waste generation, with cement production being responsible for approximately 9% of global anthropogenic CO2 emissions. A currently untapped strategy to significantly reduce thes ...

CRC Press2022

Equivalent black carbon concentration in 10 minutes time resolution, measured in the Swiss container during MOSAiC 2019/2020

Benjamin Jérémy Laurent Heutte, Julia Schmale, Ivo Fabio Beck, Lubna Dada

This dataset contains equivalent black carbon (eBC) concentrations, averaged to 10 min time resolution, measured during the year-long MOSAiC expedition from October 2019 to September 2020. The measurements were performed in the Swiss container on the D-dec ...

Zenodo2022

Deformation and Fracture of Tough Microstructured Hydrogels

Michael David Kessler

Many natural materials are structured on different length scales. This structuring often leads to an intricate interplay between soft and stiff components, which significantly improves the fracture toughness of these materials. A class of soft material tha ...

EPFL2022

Nonlinear study on a rigid rotor supported by herringbone grooved gas bearings: Theory and validation

Jürg Alexander Schiffmann, Patrick Hubert Wagner, Philipp Kaspar Bättig, Wanhui Liu

The nonlinear behavior of a rigid rotor supported by herringbone grooved journal gas bearings (HGJBs) was investigated in this study. The two-dimensional narrow groove theory (2D-NGT) was adopted to model the HGJBs. A set of integrated rotor-bearing state ...

2021

Stability and Unbalance Analysis of Rigid Rotors Supported by Spiral Groove Bearings: Comparison of Different Approaches

Jürg Alexander Schiffmann, Elia Iseli

The dynamic behavior of spiral-grooved gas bearing supported four degrees-of-freedom (DOF) rotors is investigated by means of linearized bearing force coefficients and full time-integrated transient analysis. The transient method consists of a state-space ...

2021

Computational Inverse Design of Surface-based Inflatables

Mark Pauly, Francis Julian Panetta, Florin Isvoranu, Tian Chen

We present a computational inverse design method for a new class of surface-based inflatable structure. Our deployable structures are fabricated by fusing together two layers of inextensible sheet material along carefully selected curves. The fusing curves ...

2021