Publications associées à Microstructural influence on the scatter in the fatigue life of steel reinforcement bars

Evaluation of Interface and Residual Strain of NiTi Layer Deposited on NiTiX Substrate by Laser Powder Bed Fusion

Elyas Ghafoori, Christian Leinenbach, Irene Ferretto, Mahbod Golrang, Mahshid Memarian

This study investigates the microstructure and properties of functionally graded NiTi alloy bilayers. The NiTi layer is printed by laser powder bed fusion on a NiTiX (where X is Hf or Cu) substrate prepared by vacuum arc remelting. Specimens produced with ...

Wiley-V C H Verlag Gmbh2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

Roland Logé

The microstructure evolution associated with the cold forming sequence of an Fe-14Cr-1W-0.3Ti-0.3Y2O3 grade ferritic stainless steel strengthened by dispersion of nano oxides (ODS) was investigated. The material, initially hot extruded at 1100 degrees C an ...

MDPI2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Maléna Bastien Masse, Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Strain-based analysis on the influence of local undercut geometry on fatigue crack initiation life

Alain Nussbaumer, Heikki Tapani Remes, Abinab Niraula

The local undercut defects at the weld toe provide a potential initiation site for fatigue cracks and significantly impact the structure's fatigue strength. The influence of continuous undercut depth on fatigue performance is widely studied, but the resear ...

2024

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Diego Isidoro Heredia Rosa

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

EPFL2024

A WIM-Based Assessment of Multiple Vehicle Presence Effects on Fatigue Damage of Highway Bridges

Alain Nussbaumer, Scott Walbridge, Matthew James Sjaarda

The fatigue provisions for bridge design in North America and Europe are highly simplified for the sake of practical implementation, in comparison with the state of the art in understanding of the true fatigue behavior. Historically, one significant simpli ...

2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Tension-tension fatigue behavior of basalt composite hybrid joints

Thomas Keller, Lulu Liu, Xin Wang

The tension–tension fatigue behavior of pseudo-ductile hybrid bonded-bolted double lap basalt composite joints, composed of pseudo-ductile adhesives and adherends with multi-directional fiber architecture, was experimentally investigated. The fatigue damag ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Microstructure et usinabilité d'alliages de titane béta-métastable

Loïc Favre

Titanium has become in recent years an interesting material in many applications that require a combination of high mechanical properties and low density. It has the peculiarity of undergoing an allotropic transformation at 882°C. Below this temperature, ...

EPFL2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Cyril Cayron, Roland Logé, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Vacancy segregation and intrinsic coordination defects at (111) twist grain boundaries in diamond

Christian Brandl, Carolina Baruffi

High radiation damage resistance has become increasingly important for applications of functional materials in harsh environments. The high radiation damage resistance diamond cubic carbon is a unique material which is considered for radiation environments ...

Pergamon-Elsevier Science Ltd2023

Tensile and creep-rupture response of additively manufactured nickel-based superalloy CM247LC

Christian Leinenbach, Rafal Wróbel

Tensile and creep rupture properties of crack-free CM247LC alloy, processed via laser powder bed fusion, have been characterised in this work at temperatures up to 1000 & DEG;C. The subject alloy matches or even exceeds the tensile performance of its direc ...

ELSEVIER2023

Origin of the enhanced pseudo-elasticity of additively manufactured Fe-17Mn-5Si-4Ni-10Cr-(V, C) shape memory alloy fabricated by laser powder bed fusion

Christian Leinenbach, Irene Ferretto

This study investigated the origin of the enhanced pseudo-elasticity of additively manufactured vanadium carbide-containing Fe-based shape memory alloys. The aged samples with two different starting microstructures, as-built and solution-treated, showed co ...

Elsevier Science Sa2023

Rapid grain boundary diffusion in foraminifera tests biases paleotemperature records

Lukas Baumgartner, Anders Meibom, Jaroslaw Hubert Stolarski, Arthur Adams, Deyanira Graciela Cisneros Lazaro, Jinming Guo

The paleoseawater temperature record from the oxygen isotope compositions of fossil foraminifera tests may be biased by up to about 1 degrees C due to grain-boundary diffusion alone, according to isotope exchange experiments on foraminifera tests. The oxyg ...

2023

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023