Publications associées à Uniaxial deformation of microcellular metals: model systems and simplified analysis

Publications associées (29)

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Computational Homogenization for Inverse Design of Surface-based Inflatables

Mark Pauly, Florin Isvoranu, Francis Julian Panetta, Yingying Ren, Seiichi Eduardo Suzuki Erazo, Uday Kusupati

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

Association for Computing Machinery (ACM)2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Tailored solidification microstructures for innovative use of high-density materials in lightweight products

Michel Rappaz

One approach is to tailor the solidification microstructures of lightweight components using dense materials. This study examines the microstructures and mechanical properties of near eutectic Al-Cu alloys under different thermal histories, covering both h ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

A semantic model-based systems engineering approach for assessing the operational performance of metal forming process

Dimitrios Kyritsis, Jinzhi Lu

Metal Forming is a basic and essential industrial process to provide materials for constructing complex products. To design an efficient metal forming process, the functional requirements and operational performance are two important aspects to be consider ...

Pergamon-Elsevier Science Ltd2024

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Experimental investigation of rotational behavior of pseudo-ductile adhesive angle joints exhibiting variable strain rate

Thomas Keller, Ghazaleh Eslami, Abdolvahid Movahedirad

Pseudo-ductile behavior in composite structural frames can be achieved by enabling their beam-column joints to exhibit nonlinear structural response due to progressive damage, by using pseudo-ductile adhesives. This study investigates the static behavior o ...

2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Compressive properties of a severely deformed fine-grained Mg-6Gd-3Y alloy

Roland Logé

An extruded Mg-6Gd-3Y alloy was processed by 6 passes of simple shear extrusion (SSE) at 553 K to refine the microstructure. The microstructural studies were performed through electron back-scattered diffraction (EBSD) and also transmission electron micros ...

ELSEVIER SCIENCE SA2023

Modeling the mechanics and rheology of porous and granular media: an elastoplastic continuum approach

Lars Kristoffer Uhlen Blatny

The complex mechanics of porous and granular media play a significant role in various industrial processes and natural phenomena. As an example, understanding the mechanics of how failure occurs, localizes and propagates in porous brittle solids under vari ...

EPFL2023

Laser powder bed fusion of Fe-based shape memory alloys for novel structural metamaterials and "smart" structures

Irene Ferretto

Laser powder bed fusion (LPBF) is a powder-based additive manufacturing (AM) technique, which shows great potential in the production of complex-shaped parts with unprecedented design freedom. In addition, it allows for an active manipulation of the micros ...

EPFL2023