Publications associées à Active sensing and repair composites

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

On the influence of flow-front orientation on stringer stiffened composite panels in water impacts

Véronique Michaud

Water impacts form the critical load case for high-performance carbon fibre reinforced polymer (CFRP) racing craft. Such events produce a peaked, non-uniform pressure distribution that travels along a hull panel as it is immersed. Current design standards ...

2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi, Markus Koenigsdorff

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Biobased Composites from Eugenol- and Coumarin-Derived Methacrylic Latex and Hemp Nanocellulose: Cross-Linking via [2+2] Photocycloaddition and Barrier Properties

Yves Leterrier, Sara Dalle Vacche

A novel-biobased latex was synthesized by redox-initiated emulsion copolymerization of ethoxy dihydroeugenyl methacrylate with 5 wt % of a photosensitive methacrylate containing a coumarin group. A stable copolymer latex having 16 wt % solids content and a ...

Amer Chemical Soc2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Shaped Laser Pulses for Microsecond Time-Resolved Cryo-EM: Outrunning Crystallization during Flash Melting

Marcel Drabbels, Ulrich Lorenz, Constantin Richard Krüger, Nathan Junior Mowry

Water vitrifies if cooled at rates above 3 × 105 K/s. In contrast, when the resulting amorphous ice is flash heated, crystallization occurs even at a more than 10 times higher heating rate, as we have recently shown. This may present an issue for microseco ...

2024

Flash Melting Amorphous Ice

Marcel Drabbels, Ulrich Lorenz, Constantin Richard Krüger, Gabriele Bongiovanni, Nathan Junior Mowry

Water can be vitrified if it is cooled at high rates, which makes it possible to outrun crystallization in so-called no man’s land, a range of deeply supercooled temperatures where water crystallizes rapidly. Here, we study the reverse process in pure wate ...

2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Decomposition method to evaluate district heating/cooling network potential at urban scale

Luc Girardin, François Maréchal, Raphaël Briguet, Ana Catarina Gouveia Braz, Bingqian Liu

In this work, a tool to design district heating networks (DHN) is presented and applied to the city of Lausanne as a case study. The evaluation of the buildings’ heat/cooling demand is performed using a Geographic Information System (GIS) database, built f ...

Associazione Italiana Di Ingegneria Chimica2024

Thermo-hydro-mechanical behaviour of the Callovo-Oxfordian claystone under thermal changes

Héloïse Manon Fuselier

Underground storage of radioactive waste is consensually recognised as the safest storage solution by European and worldwide countries relying mainly or partially on nuclear energy production. Over twenty years of research led by the French national agency ...

EPFL2024

Strategies for energy-efficient frontal polymerisation processing and microstructural evaluation of fibre reinforced composites

Jacobus Gerardus Rudolph Staal

Liquid composite moulding methods are widely applied for manufacturing of fibre reinforced polymer (FRP) composites and consist of two main stages: impregnation of fibrous reinforcements by a liquid monomer resin and curing of this resin. This thesis work ...

EPFL2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Recyclable flame retardant phosphonated epoxy based thermosets enabled via a reactive approach

Véronique Michaud, Valentin Rougier

The development of reusable fire-safe polymers with a prolonged lifetime heralds the switch for a transition towards circular economy. In this framework, we report a novel phosphonated thermoset which is composed of networked phosphonate esters containing ...

ELSEVIER SCIENCE SA2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mário Alexandre De Jesus Garrido, Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023

Characteristic rupture height of the mediating air film beneath an impacting drop on atomically smooth mica

John Martin Kolinski, Ramin Kaviani

Before a droplet can contact a surface during impact, it must first displace the air beneath it. Over a wide range of impact velocities, the droplet first squeezes the air into a thin film, enhancing its resistance to drainage; this slows the progress of t ...

Amer Physical Soc2023