Publications associées à Exploring the inner workings of the clove hitch knot

Publications associées (37)

Modeling friction and wear using an adaptive discrete-continuum coupling

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Capsizing due to friction-induced twist in the failure of stopper knots

Pedro Miguel Nunes Pereira de Almeida Reis, Paul Johanns

We investigate the failure mechanism of stopper knots, with a particular focus on the figure -8 knot as a representative example. Stopper knots are widely used in climbing, sailing, racket stringing, and sewing to maintain tension in ropes, strings, or thr ...

Elsevier2024

A method and system for optimizing design, implantation, and stimulation protocols of electrodes stimulating the nervous system

Silvestro Micera, Simone Romeni

A method for optimizing at least one of a geometry, an implantation procedure, and/or stimulation protocol of one or more electrodes for an electrical stimulation of a target structure in a nervous system of a living being by a computer device, the method ...

2024

Strain-based analysis on the influence of local undercut geometry on fatigue crack initiation life

Alain Nussbaumer

The local undercut defects at the weld toe provide a potential initiation site for fatigue cracks and significantly impact the structure's fatigue strength. The influence of continuous undercut depth on fatigue performance is widely studied, but the resear ...

2024

FENNECS: a novel particle-in-cell code for simulating the formation of magnetized non-neutral plasmas trapped by electrodes of complex geometries

Guillaume Michel Le Bars, Stefano Alberti, Jean-Philippe Hogge, Joaquim Loizu Cisquella, Jérémy Genoud, Francesco Romano

This paper presents the new 2D electrostatic particle -in -cell code FENNECS developed to study the formation of magnetized non -neutral plasmas in geometries with azimuthal symmetry. This code has been developed in the domain of gyrotron electron gun desi ...

2024

Investigation of mycelium film as the adhesive for poplar veneer bonding: insight into interfacial bonding mechanisms

Wenjing Sun

The emergence of mycelium-bonded biocomposites has been stimulated in the quest for sustainable development. These biocomposites exhibit enhanced mechanical properties through hot pressing, with mycelium playing a crucial role as both the adhesive and rein ...

Taylor & Francis Ltd2024

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Domain knowledge-informed synthetic fault sample generation with health data map for cross-domain planetary gearbox fault diagnosis

Olga Fink

Extensive research has been conducted on fault diagnosis of planetary gearboxes using vibration signals and deep learning (DL) approaches. However, DL-based methods are susceptible to the domain shift problem caused by varying operating conditions of the g ...

ACADEMIC PRESS LTD- ELSEVIER SCIENCE LTD2023

Computational Exploration of Multistable Elastic Knots

Mark Pauly, Yingying Ren, Michele Vidulis

We present an algorithmic approach to discover, study, and design multistable elastic knots. Elastic knots are physical realizations of closed curves embedded in 3-space. When endowed with the material thickness and bending resistance of a physical wire, t ...

Association for Computing Machinery (ACM)2023

The strength of surgical knots involves a critical interplay between friction and elastoplasticity

Pedro Miguel Nunes Pereira de Almeida Reis, Paul Johanns, Paul Grandgeorge

Knots are the weakest link in surgical sutures, serving as mechanical ligatures between filaments. Exceeding their safe operational limits can cause fatal complications. The empirical nature of present guidelines calls for a predictive understanding of the ...

AMER ASSOC ADVANCEMENT SCIENCE2023

Axial and radial axonal diffusivities and radii from single encoding strongly diffusion-weighted MRI

Erick Jorge Canales Rodriguez, Marco Pizzolato

We enable the estimation of the per-axon axial diffusivity from single encoding, strongly diffusion-weighted, pulsed gradient spin echo data. Additionally, we improve the estimation of the per-axon radial diffusivity compared to estimates based on spherica ...

ELSEVIER2023

Early decoding of walking tasks with minimal set of EMG channels

Silvestro Micera

Objective. Powered lower-limb prostheses relying on decoding motor intentions from non-invasive sensors, like electromyographic (EMG) signals, can significantly improve the quality of life of amputee subjects. However, the optimal combination of high decod ...

IOP Publishing Ltd2023

Planar Equilibria of an Elastic Rod Wrapped Around a Circular Capstan

Harmeet Singh

We present a study on planar equilibria of a terminally loaded elastic rod wrapped around a rigid circular capstan. Both frictionless and frictional contact between the rod and the capstan are considered. We identify three cases of frictionless contact - n ...

SPRINGER2022

T-5 configurations and hyperbolic systems

Riccardo Tione, Carl Johan Peter Johansson

In this paper, we study the rank-one convex hull of a differential inclusion associated to entropy solutions of a hyperbolic system of conservation laws. This was introduced in [B. Kirchheim, S. Muller and V. S(sic)ver & aacute;k, Studying Nonlinear PDE by ...

WORLD SCIENTIFIC PUBL CO PTE LTD2023

A review of materials used in tomographic volumetric additive manufacturing

Christophe Moser, Jorge Andres Madrid Wolff

Volumetric additive manufacturing is a novel fabrication method allowing rapid, freeform, layer-less 3D printing. Analogous to computer tomography (CT), the method projects dynamic light patterns into a rotating vat of photosensitive resin. These light pat ...

SPRINGER HEIDELBERG2023

Cross verified independent measurements of correlated bubble property distributions as part of the scale-up of a catalytic bubbling fluidized bed reactor

Philipp Fedor Riechmann

Methanation can be applied as part of a Power-to-Gas (PtG) concept to store renewable electricity. Using a catalytic bubbling fluidized bed (BFB) methanation reactor allows a flexible and economic operation. Properties of bubbles rising through the fluidiz ...

EPFL2022

An elastic rod in frictional contact with a rigid cylinder

Pedro Miguel Nunes Pereira de Almeida Reis, Tomohiko Sano, Paul Grandgeorge

We investigate the load transmission along an elastic rod of finite cross-section in contact with a rigid cylinder, as system often referred to as the generalized capstan problem. In the presence of friction, the idealized classic capstan equation predicts ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Damping of flexure blades based on bi-material additive manufacturing

Simon Nessim Henein, Florent Cosandier, Loïc Benoît Tissot-Daguette, Nikola Kalentics, Florent Alexandre Boudoire, Elias Sebastian Klauser

Flexure-based mechanisms have become state-of-the-art solutions for the design of high-precision mechanisms, free from friction wear, backlash, and lubrication. These properties which are necessary for applications in ultraclean or harsh environments, neve ...

2023

Bragg edge tomography characterization of additively manufactured 316L steel

Roland Logé, Christian Leinenbach, Nikola Kalentics

In this work we perform a neutron Bragg edge tomography of stainless steel 316L additive manufacturing samples, one as built via standard laser powder bed fusion, and one using the novel three-dimensional (3D) laser shock peening technique. First, we consi ...

AMER PHYSICAL SOC2022

From defect to effect: controlling electronic transport in chevron graphene nanoribbons

Oleg Yazyev, Kristians Cernevics

While bottom-up synthesis allows for precise control over the properties of graphene nanoribbons (GNRs), the use of certain precursor molecules can result in edge defects, such as missing benzene rings that resemble a 'bite'. We investigate the adverse eff ...

IOP Publishing Ltd2023