Publications associées à Tribocorrosion under fluid lubrication : modeling wear of CoCrMo artificial hip joints

Publications associées (29)

Modeling friction and wear using an adaptive discrete-continuum coupling

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

A story of two transitions: From adhesive to abrasive wear and from ductile to brittle regime

Jean-François Molinari, Sacha Zenon Wattel

Atomistic simulations performed with a family of model potential with tunable hardness have proven to be a great tool for advancing the understanding of wear processes at the asperity level. They have been instrumental in finding a critical length scale, w ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Computational fluid dynamics simulations of the heat transfer properties of graphene-based nanolubricants and application to hydrodynamic lubrication

Roberto Guarino

In this paper, we consider experimental data available for graphene-based nanolubricants to evaluate their convective heat transfer performance by means of computational fluid dynamics (CFD) simulations. Single-phase models with temperature-dependent prope ...

Aip Publishing2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Roughness Evolution Induced by Third-Body Wear

Jean-François Molinari, Tobias Brink, Antonio Joaquin Garcia Suarez

Surface roughness is a key factor when it comes to friction and wear, as well as to other physical properties. These phenomena are controlled by mechanisms acting at small scales, in which the topography of apparently flat surfaces is revealed. Roughness i ...

2024

Computational Homogenization for Inverse Design of Surface-based Inflatables

Mark Pauly, Florin Isvoranu, Francis Julian Panetta, Yingying Ren, Seiichi Eduardo Suzuki Erazo, Uday Kusupati

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

Association for Computing Machinery (ACM)2024

Fault roughness controls injection-induced seismicity

Lei Wang, Simon Guérin-Marthe

Surface roughness ubiquitously prevails in natural faults across various length scales. Despite extensive studies highlighting the important role of fault geometry in the dynamics of tectonic earthquakes, whether and how fault roughness affects fluid-induc ...

National Academy of Sciences2024

Surgical approaches to the capitellum: a comparative anatomic study

Alexandre Terrier, Patrick Goetti, Frédéric Vauclair

Background: Osteochondritis dissecans (OCD) of the humeral capitellum is an important cause of elbow disability in young athletes. Large and unstable lesions sometimes require joint reconstruction with osteochondral autograft. Several approaches have been ...

Mosby-Elsevier2024

Effect of Mo addition on the mechanical and tribological properties of magnetron sputtered TiN films

Sami Rtimi

Ternary-based titanium nitride (TiN) thin films have drawn attention toward rational applications due to their wear resistance, high hardness, and corrosion resistance. The influence of Mo content on the structural, tribo-logical, and mechanical properties ...

ELSEVIER SCIENCE SA2023

Influence of Viscous Lubricant on Nucleation and Propagation of Frictional Ruptures

Marie Estelle Solange Violay, François Xavier Thibault Passelègue, Federica Paglialunga

Fluids are pervasive in the Earth's crust and saturate fractures and faults. The combination of fluids and gouge layers developing along faults can generate fluids of different viscosities. Such viscous fluids were found to influence the reactivation, fric ...

2023

In-vivo investigation of electrochemical behavior of Ti and CoCrMo alloy in human synovial fluids

Yueyue Bao

With the development of modern medical techniques, the application of orthopedic implants has been continually increasing in recent years. Passive materials, such as Ti and its alloys as well as CoCrMo alloys, are widely used in artificial joints due to th ...

EPFL2023

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Nanoindentation of embedded particles

Andreas Mortensen, Alejandra Inés Slagter, Joris Pierre Everaerts

We address the effect of elastic inhomogeneity on elastic modulus and hardness determinations made by depth-sensing indentations performed on individual particles embedded within a matrix of different elastic modulus. Finite element simulations and nanoind ...

SPRINGER HEIDELBERG2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

State-Based Versus Time-Based Estimation of the Gait Phase for Hip Exoskeletons in Steady and Transient Walking

Auke Ijspeert, Mohamed Bouri, Ali Reza Manzoori

The growing demand for online gait phase (GP) estimation, driven by advancements in exoskeletons and prostheses, has prompted numerous approaches in the literature. Some approaches explicitly use time, while others rely on state variables to estimate the G ...

IEEE2023