Publications associées à Structural response of fiber-polymer composite bending-active elastica members under short- and long-term loading conditions

Publications associées (16)

C-shells: Deployable Gridshells with Curved Beams

Mark Pauly, Francis Julian Panetta, Yingying Ren, Quentin Christian Becker, Seiichi Eduardo Suzuki Erazo, Davide Pellis

We introduce a computational pipeline for simulating and designing C-shells, a new class of planar-to-spatial deployable linkage structures. A C-shell is composed of curved flexible beams connected at rotational joints that can be assembled in a stress-fre ...

Association for Computing Machinery (ACM)2023

Swelling and shrinkage of partially saturated gas shales: from laboratory tests to an effective stress framework

Jinwoo Kim

Gas shale swelling during hydraulic stimulation is one of the major challenges in unconventional gas development. It is hypothesized that the large volumetric strain upon water imbibition is a consequence of dramatic changes in capillary pressure and disjo ...

EPFL2022

Post-tensioning of glass beams: Analytical determination of the allowable pre-load

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

The effectiveness of post-tensioning in enhancing the fracture resistance of glass beams depends on the level of compressive pre-stress introduced at the glass edge surface that will in service be exposed to tensile stresses induced by bending. Maximum pre ...

2021

Development of a Mechanical Wedge-Barrel Anchor for CFRP Rods: Static and Fatigue Behaviors

Alain Nussbaumer, Elyas Ghafoori, Masoud Motavalli, Hossein Heydarinouri

In this study, a mechanical anchorage for prestressed carbon fiber-reinforced polymer (CFRP) rods was proposed. The proposed anchorage consisted of a steel barrel with a conical hole and three separate aluminum wedges that are in direct contact with the CF ...

ASCE-AMER SOC CIVIL ENGINEERS2021

The influence of transverse reinforcement and yielding of flexural reinforcement on the shear-transfer actions of RC members

Miguel Fernández Ruiz

The assessment of the shear strength of reinforced concrete beams with and without shear reinforcement is investigated in this paper on the basis of the contribution of the various potential shear-transfer actions. To that aim, a comprehensive experimental ...

2021

The effect of the elongation of the proximal aorta on the estimation of the aortic wall distensibility

Nikolaos Stergiopoulos, Vasiliki Bikia, Bram Trachet, Georgios Rovas, Stamatia Zoi Pagoulatou, Mauro Ferraro

The compliance of the proximal aortic wall is a major determinant of cardiac afterload. Aortic compliance is often estimated based on cross-sectional area changes over the pulse pressure, under the assumption of a negligible longitudinal stretch during the ...

2021

Fiber-based hysteretic model for simulating strength and stiffness deterioration of steel hollow structural section columns under cyclic loading

Dimitrios Lignos

An efficient component model has been developed that captures strength and stiffness deterioration of steel hollow structural section (HSS) columns. The proposed model consists of two fiber-based segments at a member's ends along with an elastic segment in ...

2020

Time-resolved open-circuit conductive atomic force microscopy for direct electromechanical characterisation

Anna Fontcuberta i Morral, Wonjong Kim, Jelena Vukajlovic Plestina

Studying nanomaterial piezoelectricity and triboelectricity is attractive for energy and sensing applications. However, quantitative characterisation of electromechanical effects in nanomaterials is challenging due to practical limitations and possible com ...

2020

Efficient decellularization of equine tendon with preserved biomechanical properties and cytocompatibility for human tendon surgery indications

Pierre-Arnaud Aeberhard, Dominique Pioletti, Lee Ann Laurent-Applegate, Nathalie Hirt-Burri, Jens Antons, Anthony Grognuz

Chronic and acute tendon injuries are frequent afflictions, for which treatment is often long and unsatisfactory. When facing extended injuries, matrices and scaffolds with sufficient biomechanical properties are required for surgical repair and could addi ...

2020

Influence of thermo-mechanical processing on ordering kinetics in 18 karat red gold alloy

Marina Garcia Gonzalez

The aim of this project is to understand the correlation between alloy composition and the build-up of internal stresses in 18 carat Au-Ag-Cu alloys under thermo-mechanical loads. The copper rich end of this ternary system exhibits order-hardening of the e ...

EPFL2020

Comparing methodologies for structural identification and fatigue life prediction of a highway bridge

Ian Smith, Alain Nussbaumer, Sai Ganesh Sarvotham Pai

Accurate measurement-data interpretation leads to increased understanding of structural behavior and enhanced asset-management decision making. In this paper, four data-interpretation methodologies, residual minimization, traditional Bayesian model updatin ...

2018

A new hybrid Additive Manufacturing process combining Selective Laser Melting and Laser Shock Peening

Nikola Kalentics

Additive Manufacturing (AM) in whole and especially Selective Laser Melting (SLM) are already making a revolution in the way parts are designed and manufactured with the ability to produce lightweight parts with unprecedented complex geometries which are o ...

EPFL2018

Stress-Induced Depression: Is Social Rank a Predictive Risk Factor?

Maria del Carmen Sandi Perez, Thomas Didier Larrieu

An intriguing question in the field of stress is what makes an individual more likely to be susceptible or resilient to stress‐induced depression. Predisposition to stress susceptibility is believed to be influenced by genetic factors and early adversity. ...

2018

Engineered substrates with embedded strain relief for stretchable thin-film electronics

Alessia Romeo

Stretchable electronics are integrated circuitry that can reversibly expand and relax while retaining their functionality. This emerging technology has great potential in unconventional electronic application areas, especially in biomedical sector. To atta ...

EPFL2015

Detecting emotional stress from facial expressions for driving safety

Jean-Philippe Thiran, Anil Yuce, Hua Gao

Monitoring the attentive and emotional status of the driver is critical for the safety and comfort of driving. In this work a real-time non-intrusive monitoring system is developed, which detects the emotional states of the driver by analyzing facial expre ...

2014

Formation of drying crack patterns in soils : a deterministic approach

Lyesse Laloui, Hervé Péron

Soils, as well as most of deformable multiphase porous materials, are likely to suffer from desiccation cracking, leading to the formation of regular crack patterns affecting their permeability. The ensuing cracks spacing has often been related to a concep ...

Springer Verlag2013