Combining alloy and process modification for micro-crack mitigation in an additively manufactured Ni-base superalloy

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (31)

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

Cyril Cayron, Roland Logé, Baptiste Thomas Jean Rouxel

Cu-Be alloys provide excellent electrical and mechanical properties, but present serious health hazards during manufacturing. Among alternative alloys, the Cu-Ti system has the highest yield strength; however, Ti cannot be easily solutionized at concentrat ...

ELSEVIER SCI LTD2022

A Low-Temperature Annealing Method for Alloy Nanostructures and Metasurfaces: Unlocking a Novel Degree of Freedom

Christian Santschi, Olivier Martin, Debdatta Ray, Jeonghyeon Kim, Hsiang-Chu Wang

The material and exact shape of a nanostructure determine its optical response, which is especially strong for plasmonic metals. Unfortunately, only a few plasmonic metals are available, which limits the spectral range where these strong optical effects ca ...

Wiley-V C H Verlag Gmbh2022

Machine learning for metallurgy IV: A neural network potential for Al-Cu-Mg and Al-Cu-Mg-Zn

William Curtin, Daniel John Gilles Marchand

Most metallurgical properties, e.g., dislocation propagation, precipitate formation, can only be fully understood atomistically but most phenomena and quantities of interest cannot be measured experimentally. Accurate simulation methods are essential but f ...

2022

Development of High-Strength Aluminum Alloys for Additive Manufacturing

Marvin Lennard Schuster

Metal additive manufacturing (AM) offers the possibility to rapidly produce complex geometries that are not achievable with conventional manufacturing methods. The two most common technologies, Laser Powder Bed Fusion (LPBF) and Direct Metal Deposition (DM ...

EPFL2022

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials. Part II: Experimental verification of modelling approaches by infiltration of Si-Zr alloy into idealized microchannels

Ludger Weber, Giovanni Bianchi, Alberto Ortona, Manoj Kondibhau Naikade, Caroline Hain

In this work, the mechanisms leading to the pore closure in reactive melt infiltration (RMI) of carbon by pure silicon and a near eutectic Si-8 at-pct Zr alloy at 1500 and 1700 degrees C under vacuum were studied. Various geometrical configurations of micr ...

ELSEVIER SCI LTD2022

Effect of chromium content on microstructural evolution of CoNiAlW superalloy

Cyril Cayron

Effects of chromium (Cr) content on types and morphologies of various phases of a newly developed Co-Ni-Al-W superalloy (Co-30Ni-6W-9Al-3Ti-1Ta) have been investigated in this study. Microstructural examinations were carried out by field-emission scanning ...

SPRINGER HEIDELBERG2022

Phase and microstructure selection in peritectic alloys under high G-V ratio

Stéphane Dobler, Wilfried Kurz

A new model for the case of a superposition of a phase transformation and a microstructure transition from columnar plane front to equiaxed dendritic growth for peritectic alloys is presented. This model is applied to Fe-Ni alloys where a phase transition ...

WALTER DE GRUYTER GMBH2022

Experimental investigation of dowel action using advanced measurement techniques

Aurelio Muttoni, Marko Pejatovic

Existing shear-cracked structures need to be reliably verified in order to avoid redundant interventions. Code provisions often raise shear safety and/or fatigue life concerns of the reinforcement subjected to stress concentrations due to cyclic dowel acti ...

2022

A ductility criterion for bcc high entropy alloys

William Curtin, Binglun Yin, Eleanor Yi Kei Mak

A current goal driving alloy development is the identification of alloy compositions for high temperature applications but with the additional requirement of sufficient ductility at ambient temperatures. Multicomponent, single-phase, polycrystalline High E ...

PERGAMON-ELSEVIER SCIENCE LTD2021

Atomic scale investigations of fracture in metal alloys

Eleanor Yi Kei Mak

The demand for metal alloys with superior structural performance in industrial applications continues to increase, as does the need for more-energy efficient materials and methods. Many materials that are otherwise attractive for structural applications ar ...

EPFL2021

Laser powder-bed fusion of metallic alloys with enhanced microstructures and properties

Navid Sohrabi

Laser powder-bed fusion (LPBF) is an additive manufacturing (AM) process that uses a laser to selectively melt a powder bed. This process can build dense samples with complicated geometries from a wide variety of metallic alloys. In this thesis, LPBF of al ...

EPFL2021

Page 2 sur 2