Publications associées à Dynamic Properties of Materials for Alpine Skis

Customized modular multi-material mouthguard and method of making the same

Dominique Pioletti, Martin Broome, Naser Nasrollahzadeh Mamaghani

There is described a mouthguard comprising an externally exposed impact protective region defined by a first material property and configured to cover a front tooth, an internally exposed occlusional cushioning region defined by a second material property ...

2024

Searching for the Thinnest Metallic Wire

Nicola Marzari, Davide Campi

One-dimensional materials have gained much attention in the last decades: from carbon nanotubes to ultrathin nanowires to few-atom atomic chains, these can all display unique electronic properties and great potential for next-generation applications. Exfol ...

Amer Chemical Soc2024

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

Computational Homogenization for Inverse Design of Surface-based Inflatables

Mark Pauly, Francis Julian Panetta, Uday Kusupati, Yingying Ren, Florin Isvoranu, Seiichi Eduardo Suzuki Erazo

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Morphological and Material Programability of a Hall-Effect Based Soft Tactile Sensors

Josephine Anna Eleanor Hughes, Sudong Lee

The different receptors in human skin show not only diversity in the stimuli to which they respond, but also variable sensitivity and directionality. This is often determined by their location or morphology, and can play an important role in filtering or a ...

IEEE2024

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mário Alexandre De Jesus Garrido, Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Supramolecular Modifications of Semicrystalline Polymers

Michael Alan Giffin

Supramolecular interactions play an important role in defining the structure and the resulting mechanical properties of materials. For instance, interchain hydrogen-bonding in PAs gives them superior strength and stiffness in engineering materials, while t ...

EPFL2023

Rheological Properties of Ionically Crosslinked Viscoelastic 2D Films vs. Corresponding 3D Bulk Hydrogels

Esther Amstad, Gaia De Angelis

Ionically crosslinked hydrogels containing metal coordination motifs have piqued the interest of researchers in recent decades due to their self-healing and adhesive properties. In particular, catechol-functionalized bulk hydrogels have received a lot of a ...

AMER CHEMICAL SOC2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Dynamic Modeling of an Origami Prismatic Joint

Jamie Paik, Jian-Lin Huang, Mustafa Mete

Dynamic modeling of folding joints is critical for predicting dynamic behavior, optimizing design parameters, and developing control strategies for origami robots and machines. Although kinematics of the folded joints exists, little research describes thei ...

IEEE2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

Deformation and Fracture of Tough Microstructured Hydrogels

Michael David Kessler

Many natural materials are structured on different length scales. This structuring often leads to an intricate interplay between soft and stiff components, which significantly improves the fracture toughness of these materials. A class of soft material tha ...

EPFL2022

Real space and reciprocal space investigations of the spin dynamics in skyrmion-hosting materials

Le Yu

Magnetic skyrmions are whirl-like spin configurations with particle-like properties protected by non-trivial topology. Due to their unique spin structures and dynamical properties, they have attracted tremendous interests over the past decade, from fundame ...

EPFL2022

Hydro-processing of biomass using novel metal-organic framework (MOF)/polymer composite catalysts

Vikram Vinayak Karve

Generating value, in the form of functional chemicals, from biomass is a critical need of today. It is expected that replacing petroleum with biomass as the source of many commodity and fine chemicals can lead the transition away from a fossil-fuel based e ...

EPFL2022

Manufacturing and toughening effects on the material properties of wind turbine blade adhesives

Anastasios Vassilopoulos, Dharun Vadugappatty Srinivasan

Hybrid adhesives can be developed using commercially available adhesive materials and customized to the required loading conditions. In this paper, SPABONDTM 820HTA (non-toughened) and SPABONDTM 840HTA (toughened) adhesives are hybridized by two strategies ...

2022

Fluorinated Tetraarylethenes: Universal Tags for the Synthesis of Solid State Luminogens

Kay Severin, Rosario Scopelliti, Euro Solari, Albert Ruggi, Farzaneh Fadaei Tirani, Abdusalom Suleymanov, Thibault Jacques Marie Damiens Vanrapenbusch, Barbara Maja Kraus

The aggregation-induced emission properties of tetraarylethenes (TAEs) have led to numerous applications in chemistry, biology, and materials science. Herein, we describe two fluorinated tetraarylethenes, which can be employed as universal tags for the syn ...

Wiley-VCH Verlag GmbH2022

Extraction and controlled functionalization of lignin for materials applications

Stefania Bertella

Lignin is a renewable aromatic polymer that due to its abundance and unique chemical structure is a promising candidate to replace aromatic materials that are currently sourced from fossil oil. The same structure of lignin poses however drawbacks for its v ...

EPFL2022