Publications associées à New provisions for punching shear in Model Code 2010 based on the Critical Shear Crack Theory

Publications associées (28)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Low-tech methods for the reuse of reinforced concrete structural elements

Nicole Widmer, Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

Most of existing buildings are made of concrete, new buildings are being built with it and others are demolished when still in good structural condition. This drives increased demands for raw materials, greenhouse gas emissions, and an accumulation of demo ...

2023

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Computational Conceptual Design – Typological Exploration Of Spatial Truss Systems Through Optimization

Corentin Jean Dominique Fivet, Jonas Warmuth

Exploring a wide range of relevant design options from the outset is crucial for every sound conceptual design process. Optimization techniques are generally employed to generate well-performing structural design options. However, focusing only on performa ...

2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Computational conceptual design — typological exploration of spatial truss systems through optimization

Corentin Jean Dominique Fivet, Jonas Warmuth

Exploring a wide range of design options is crucial for every sound conceptual design process. In the conventional structural design workflow, optimization techniques are generally employed to generate well-performing design options. However, focusing only ...

International Association for Shell and Spatial Structures (IASS)2023

Interactive design with optimum matchmaking of reused structural elements – a software implementation

Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Jonas Warmuth

Structural systems are a significant contributor to buildings’ embodied carbon and reusing structural elements in new load-bearing applications is one strategy to reduce this impact. However, integrating this approach into existing design workflows without ...

International Association for Shell and Spatial Structures (IASS)2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Reinforcement bond performance in 3D concrete printing: Explainable ensemble learning augmented by deep generative adversarial networks

Xianlin Wang

Integrating various reinforcements into 3D concrete printing (3DCP) is an efficient method to satisfy critical requirements for structural applications. This paper explores an explainable ensemble machine learning (EML) method to predict the bond failure m ...

Elsevier2023

Design of slender and squat reinforced concrete members with shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Marko Pejatovic

As proposed in several design standards for structural concrete, including Eurocode 2 (EN:1992-1-1:2004) and fib's Model Code 2010, the shear design of slender members with shear reinforcement can be performed by means of consistent models based on suitabl ...

ERNST & SOHN2022

Auto-tuning deep forest for shear stiffness prediction of headed stud connectors

Xianlin Wang

The shear stiffness of headed stud connector is a critical parameter for the calculation of deflection and inter-facial shear force for steel-concrete composite structure. Thus, this study presented a promising data-driven model auto-tuning Deep Forest (AT ...

2022

Influence of sustained loading on resistance and deformation capacity of reinforced concrete members in compression

Aurelio Muttoni, Miguel Fernández Ruiz, Xhemsi Malja

As acknowledged explicitly or implicitly in most of current design codes, a high level of sustained loading has a detrimental effect on the concrete compressive strength. However, its beneficial effect in terms of deformation capacity is neglected in most ...

ERNST & SOHN2022

Influence of amount of shear reinforcement and its post-yield response on the shear resistance of reinforced concrete members

Aurelio Muttoni, Miguel Fernández Ruiz, Frédéric Monney

The minimum amount of shear reinforcement to be provided in reinforced concrete members has been a topic of debate and research for decades without reaching a consensus. Defining such values is however instrumental to build in an economic manner and to saf ...

ERNST & SOHN2022