Publications associées à Adhesively bonded joints composed of pultruded adherends: considerations at the upper tail of material strength statistical distribution

Publications associées (28)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

A story of two transitions: From adhesive to abrasive wear and from ductile to brittle regime

Jean-François Molinari, Sacha Zenon Wattel

Atomistic simulations performed with a family of model potential with tunable hardness have proven to be a great tool for advancing the understanding of wear processes at the asperity level. They have been instrumental in finding a critical length scale, w ...

2024

Micro modeling of irregular stone masonry walls using mathematical programming

Katrin Beyer, Qianqing Wang, Ketson Roberto Maximiano Dos Santos

While understanding the shear strength of stone masonry structures is important for the design and the mainte- nance, we still lack computational tools for predicting the strength as a function of the stone layout. Here we implement an end-to-end image bas ...

Springer2024

Effects of Hyporheic Exchange and Settlement on the Particle Size Distribution of Colloids

David Andrew Barry, Qihao Jiang

Colloid particle size plays an important role in contaminant adsorption and clogging in the hyporheic zone, but it remains unclear how the particle size changes during the transport of colloids. This study investigated the variation of the particle size of ...

Springer2024

One-Pass Generation of Multivariate Time Series through Conditional Multivariate Modeling

Florent Evariste Forest

In recent years, exploring deep generative models for generating time series has garnered significant interest within the research community. These models have found wide-ranging applications in areas such as data augmentation, scenario simulation, and the ...

Institute of Electrical and Electronics Engineers Inc.2024

Role of Minimum Adhesive Wear Particle Size in Third-Body Layer Properties

Jean-François Molinari, Son-Jonathan Pham-Ba

We employ a novel discrete element method (DEM) force formulation to simulate adhesive wear and assess the effects of material and loading parameters on the properties of the third-body layer (TBL) formed during sliding motion. The study emphasizes the rol ...

2023

Beyond the ultradeep frontier fields and legacy observations (BUFFALO): a high-resolution strong plus weak-lensing view of Abell 370

David Richard Harvey

The HST treasury programme BUFFALO provides extended wide-field imaging of the six Hubble Frontier Fields galaxy clusters. Here we present the combined strong and weak-lensing analysis of Abell 370, a massive cluster at z = 0.375. From the reconstructed to ...

OXFORD UNIV PRESS2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

swissALPS: a Dataset for Imbalanced Land Cover Mapping in Alpine Regions

Valérie Zermatten

Our dataset consists of very high-resolution aerial images (50cm) and a digital elevation model (50cm) that covers approx. 2300 km2 of land above 2000m altitude in the southwestern part of Switzerland. Our land cover labels focus on alpine land cover that ...

IEEE DataPort2023

Bringing casting to microfabrication: processing and deformation of microcastings

Luciano Borasi

This work extends the range of pathways for the production of metallic microcomponents by downscaling metal casting. This is accomplished by using either of two different molding techniques, namely femtosecond laser micromachining or lithographic silicon m ...

EPFL2023

Current propagation type self-consistent leader-return stroke model

Farhad Rachidi-Haeri, Marcos Rubinstein

A current propagation type return stroke model which is consistent with the estimated distribution of the charge on the leader channel is described. The model takes into account the dispersion of the return stroke current along the return stroke channel. T ...

Elsevier2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Two antagonistic response regulators control Pseudomonas aeruginosa polarization during mechanotaxis

Alexandre Louis André Persat, Lorenzo Anton-Louis Talà, Xavier Jean-Yves Pierrat, Zaïnebe Dhirani, Marco Julian Kühn

The opportunistic pathogen Pseudomonas aeruginosa adapts to solid surfaces to enhance virulence and infect its host. Type IV pili (T4P), long and thin filaments that power surface-specific twitching motility, allow single cells to sense surfaces and contro ...

WILEY2023

System for automated and dynamic cell culture

Julia Tischler

The present relates to a system for automated cell culture, the system comprising an inflow module, a cell culture plate and an outflow module, said inflow module being in fluid connection with the outflow module via the cell culture plate, the inflow modu ...

2023

Simultaneous strength and ductility enhancement of wire-arc directed energy deposited Al-Cu alloy by interlayer laser shock peening

Ke Huang, Yandong Jing

Wire-arc directed energy deposition (wire-arc DED), recognized for its ability to produce large-scale parts, has gained considerable attention. However, a critical issue with this method is the high prevalence of internal porosity defects found in the manu ...

Elsevier Science Sa2023