Development of physical and mechanical properties of a cold-curing structural adhesive in a wet bridge environment

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (32)

Page 2 sur 2

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Shear strength and shear stiffness analysis of compacted Wyoming-type bentonite

Alessio Ferrari

Wyoming-type bentonite is one of the materials to be used as part of the Engineered Barrier System (EBS) in deep geological disposal facilities for the safe disposal of spent nuclear fuel.In the KBS-3 type repository, the canisters containing the spent fue ...

ELSEVIER2023

Equivalent Frame Models for FRP-Strengthened Masonry Buildings

Fibre-reinforced polymers (FRP) strengthening can be applied to decrease the seismic vulnerability of existing masonry buildings, both with regard to in-plane and out-of-plane failure mechanisms. Experimentally, the impact of strengthening solutions has be ...

Proceedings of the 2nd Croatian Conference on Earthquake Eng2023

Quantitative study of the thickness-dependent stress in indium tin oxide thin films

Blaise François Cuénod, Rémy David Désiré Juttin

A quantitative analysis of stress in indium tin oxide (ITO) films with varying thicknesses was conducted using high-precision stylus profilometry. The experimental results revealed a transition of the stress type from tensile to compressive as the ITO film ...

Elsevier Science Sa2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

On the Post-peak Behaviour of Remoulded and Jointed Clay Samples During Triaxial Compression Tests

Alessio Ferrari

The note presents a selection of the results of a large experimental program conducted with the aim of characterizing the shear strength of Opalinus Clay and Speswhite Kaolin in remoulded and reconstituted conditions, through the execution of unconventiona ...

2023

The General Crack Component Model for reversed cyclic shear

David Michael Volpe Ruggiero

A growing body of research has shown that reversed cyclic shear loading of reinforced concrete (RC) causes effects that are not accounted for in monotonic behavioral models. Notable among these effects are a reduction in shear strength and significant plas ...

2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

3D printed fiber-optic nanomechanical bioprobe

Sandor Kasas, Jiangtao Zhou

Ultrasensitive nanomechanical instruments, e.g. atomic force microscopy (AFM), can be used to perform delicate biomechanical measurements and reveal the complex mechanical environment of biological processes. However, these instruments are limited because ...

IOP Publishing Ltd2023

Experiments and proposed model for residual stresses in hot-rolled wide flange shapes

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Andronikos Skiadopoulos

This paper proposes a new residual stress model for hot-rolled wide flange steel cross sections. For this purpose, a dataset of 85 residual stress measurements is first assembled. The dataset is comprised of prior measurements available in the literature t ...

2023

Scanning Small-Angle X-ray Scattering of Injection-Molded Polymers: Anisotropic Structure and Mechanical Properties of Low-Density Polyethylene

Marianne Liebi, Manuel Guizar Sicairos

Injection molding is known to create a layered anisotropicmorphologyacross the sample thickness due to varying shear and cooling ratesduring the manufacturing process. In this study, scanning small-angleX-ray scattering was used to visualize and quantify t ...

AMER CHEMICAL SOC2023

Benchmark study of undrained triaxial testing of Opalinus Clay shale: Results and implications for robust testing

Lyesse Laloui, Alessio Ferrari, Alberto Minardi

Triaxial testing of argillaceous rocks and shales is significantly more challenging than conventional rock mechanical testing. The challenges are mainly related to the very low permeability of these geomaterials, and their sensitivity to exposure of atmosp ...

ELSEVIER2021