Publications associées à Influence of sustained loading on resistance and deformation capacity of reinforced concrete members in compression

Publications associées (37)

A Multiaxial Plasticity Model with Softening for Simulating Inelastic Cyclic Local Buckling in Steel Beam Columns Using Fiber Elements

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Diego Isidoro Heredia Rosa

This paper proposes a new effective multiaxial plasticity model to simulate inelastic cyclic buckling in steel frame members. The proposed constitutive formulation is expressed within the framework of rate-independent metal plasticity and replicates the pr ...

American Society of Civil Engineers (ASCE)2025

Pedagogy of an interdisciplinary, hands-on workshop to design and build floor systems with reused materials

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer, Barbara Ludivine Justine Lambec, Peter Zurbrügg

This paper reflects on the pedagogy used for a series of student workshops on building with reused materials at the Ecole Polytechnique Fédérale de Lausanne (EPFL) and presents the results of its 7 th edition, which focused on floor systems. During these w ...

CRC Press2025

Understanding imbibition in cementitious materials including C-S-H strain measurement and geometric restriction

Maya Nicole Harris

Cementitious materials show anomalous behaviour during capillary imbibition: a lack of linearity of the mass gain versus the square root of time. This is considered to be caused by the water retention in the calcium silicate (C-S-H) structure (and conseque ...

2025

Additive Manufacturing of Metal Matrix Composites for Space Applications

Gaëtan Bernard

Titanium-based Metal Matrix Composites (MMCs) offer remarkable mechanical, thermal, and corrosion resistance properties and are of high interest to several industrial sectors, including aerospace. One of the main commercial drawbacks of these materials, wh ...

EPFL2025

Texture-enhanced Mechanical Stability of Transparent Electrodes for Flexible Optoelectronics with Near-infrared Response

Simon Baptiste Rieckhoff

Transparent electrodes with high conductivity and mechanical robustness are essential for flexible opto-electronic applications. Indium tin oxide (ITO) single layers have long been considered as unsuitable for flexible applications due to their brittleness ...

WILEY2025

Engineering Symmetry Breaking Interfaces by Nanoscale Structural-Energetics in Orthorhombic Perovskite Thin Films

Duncan Thomas Lindsay Alexander, Bernat Mundet

The atomic configuration of phases and their interfaces is fundamental to materials design and engineering. Here, we unveil a transition metal oxide interface, whose formation is driven by energetic influences─epitaxial tensile strain versus oxygen octahed ...

2025

Estimation of Stiffness Maps in Deforming Cells Through Optical Flow With Bounded Curvature

Michaël Unser

The stiffness of cells and of their nuclei is a biomarker of several pathological conditions. Current measurement methods rely on invasive physical probes that yield one or two stiffness values for the whole cell. However, the internal distribution of cell ...

Institute of Electrical and Electronics Engineers2025

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Corentin Jean Dominique Fivet, Célia Marine Küpfer

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

Mesh-based topology, shape and sizing optimization of ribbed plates

Ahmad Abdulrahman Ahmad Majdouba

In this paper, we present a new parameterization and optimization procedure for minimizing the weight of ribbed plates. The primary goal is to reduce embodied CO2 in concrete floors as part of the effort to diminish the carbon footprint of the construction ...

Springer2024