Publications associées à Numerical modelling of energy piles in saturated sand subjected to thermo-mechanical loads

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Corentin Jean-Marie Rémi Noël

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

2023

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Proliferation-driven mechanical compression induces signalling centre formation during mammalian organ development

Pengfei Xu, Sangwoo Kim

Localized sources of morphogens, called signalling centres, play a fundamental role in coordinating tissue growth and cell fate specification during organogenesis. However, how these signalling centres are established in tissues during embryonic developmen ...

Nature Portfolio2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Abdolvahid Movahedirad, Lulu Liu

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

RE:SLAB — a load bearing system for open-ended component reuse in building structures

Dario Redaelli, Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Alex-Manuel Muresan, Edisson Xavier Estrella Arcos

The construction industry plays a major role in the high levels of greenhouse gas emissions, resource consumption, and waste generation observed nowadays. Key to the circular economy, structural component reuse arises as a promising solution to divert cons ...

2024

Ultrahigh-quality-factor micro- and nanomechanical resonators using dissipation dilution

Tobias Kippenberg, Nils Johan Engelsen, Alberto Beccari

Mechanical resonators are widely used in sensors, transducers and optomechanical systems, where mechanical dissipation sets the ultimate limit to performance. Over the past 15 years, the quality factors in strained mechanical resonators have increased by f ...

Nature Portfolio2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Modeling the mechanics and rheology of porous and granular media: an elastoplastic continuum approach

Lars Kristoffer Uhlen Blatny

The complex mechanics of porous and granular media play a significant role in various industrial processes and natural phenomena. As an example, understanding the mechanics of how failure occurs, localizes and propagates in porous brittle solids under vari ...

EPFL2023

A fully-coupled highly-parallelized geomechanical simulator for assessing induced seismicity

Jean-François Molinari, Guillaume Anciaux, Nicolas Richart, Brice Tanguy Alphonse Lecampion, Emil Gallyamov

Induced seismicity caused by anthropogenic modification of the subsurface effective stress state has been observed in a number of industrial applications -- from hydrocarbon extraction (e.g., Groningen [1]), drilling waste-water disposal (e.g., [2]) to the ...

2023

Data-driven 1D wave propagation for site response analysis

Jean-François Molinari, Sacha Zenon Wattel, Antonio Joaquin Garcia Suarez

Prediction of ground motion triggered by earthquakes is a prime concern for both the seismology community and geotechnical earthquake engineering one. The subfield occupied with such a problem is termed site response analysis (SRA), its one-dimensional fla ...

WILEY2023

How to Make Elastomers Piezoelectric?

Frank Nüesch, Francis Owusu

Piezoelectrics play a significant role in modern electronics and electric devices. Thermal or mechanical stress on such materials induces a change in polarization generating an electric response, which is the sole effect of why they are so interesting. How ...

Wiley2023

Bounding the localized to ductile transition in porous rocks: implications for geo-reservoirs

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer

Porous rocks have long been the focus of intense research driven by their importance in our society as host to our most essential resources (oil, gas, water, geothermal energy, etc), yet their rheology remains poorly understood. With increasing depth, poro ...

2023

Mechanics, Modeling, and Upscaling of Biocemented Soils: A Review of Breakthroughs and Challenges

Lyesse Laloui, Dimitrios Terzis, Ray Harran

Biogeotechnical research has inspired revolutionary ideas to claim the status of a distinctive branch of geotechnical engineering. Most notably, underground carbonate mineralization, most commonly referred to as microbially induced carbonate precipitation ...

ASCE-AMER SOC CIVIL ENGINEERS2023

Drained Clay-Pipe Interface Resistance at Low Normal Stresses and Elevated Temperatures

Roba Houhou

Offshore pipelines that transport hydrocarbons under high pressure and high temperature are usually thermally insulated to maintain an elevated temperature and prevent any heat loss to the surroundings. However, the temperatures at the outer-wall of the pi ...

AMER SOC CIVIL ENGINEERS2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Cyril Cayron, Roland Logé, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Experimental investigation of rotational behavior of pseudo-ductile adhesive angle joints exhibiting variable strain rate

Thomas Keller, Abdolvahid Movahedirad, Ghazaleh Eslami

Pseudo-ductile behavior in composite structural frames can be achieved by enabling their beam-column joints to exhibit nonlinear structural response due to progressive damage, by using pseudo-ductile adhesives. This study investigates the static behavior o ...

2023