Combining neutron diffraction and imaging for residual strain measurements in a single crystal turbine blade

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (30)

FEM of stress partition during compression of WC-10 wt.% Co with realistic 3D morphology

Daniele Mari, Lucas Eric Jacques Degeneve

A Finite Element Model is developed to represent the mechanical behavior of WC-10 wt.% Co in compression tests. In this research, realistic three-dimensional model is obtained by slicing a sample by Focused Ion Beam and reconstituting it, resulting in two ...

ELSEVIER SCI LTD2022

Quantifying the Solution Structure of Metal Nanoclusters Using Small-Angle Neutron Scattering

Francesco Stellacci, Stefan Guldin, Zhi Luo, Ye Yang, Huayan Yang

Metal nanoclusters are a unique class of synthetic material, as their crystal structures can be resolved using X-ray diffraction, and their chemical formula can be precisely determinated from mass spectroscopy. However, a complete structure characterizatio ...

Wiley-VCH Verlag GmbH2022

Tailored deformation behavior of 304L stainless steel through control of the crystallographic texture with laser-powder bed fusion

Christian Leinenbach, Roland Logé, Efthymios Polatidis, Markus Strobl

Laser-powder bed fusion (L-PBF) has gained significant research interest, not only for its profound advantage of producing near-net shape complex geometries of metallic parts, but also for the possibility of producing tailored microstructures. Here we expl ...

ELSEVIER SCI LTD2022

Static and dynamic properties of non-collinear quantum antiferromagnets explored by neutron scattering

Luc Testa

This thesis is devoted to the investigation of static and dynamic properties of two different sets of quantum magnets with neutron scattering techniques and the help of linear spin wave theory. Both systems are copper-based with spin-1/2, which makes them ...

EPFL2021

Investigation of residual stresses in planar dissimilar magnetic pulse welds by neutron diffraction

Jean-Marie Drezet

Residual stresses are investigated for the first time in a dissimilar AA1050-DP450 steel magnetic pulse weld using neutron diffraction. Close to the joint interface, tensile residual stresses are observed in the Al sheet and compressive residual stresses a ...

ELSEVIER SCI LTD2021

Nondestructive characterization of laser powder bed fusion parts with neutron Bragg edge imaging

Christian Leinenbach, Roland Logé, Nikola Kalentics, Markus Strobl

Laser powder bed fusion is an efficient technique for additive manufacturing of metallic materials. The quality of the material produced depends on the optimization of a large range of build parameters and the complex thermo-mechanical build process is pro ...

ELSEVIER2021

Crystallization kinetics of atomic crystals revealed by a single-shot and single-particle X-ray diffraction experiment

Giorgio Rossi, Christoph Bostedt, Alessandro Colombo

Crystallization is a fundamental natural phenomenon and the ubiquitous physical process in materials science for the design of new materials. So far, experimental observations of the structural dynamics in crystallization have been mostly restricted to slo ...

National Academy of Sciences2021

Design of the third-generation lead-based neutron spallation target for the neutron time-of-flight facility at CERN

Roland Logé, Nicola Colonna, Raffaele Esposito

The neutron time-of-flight (n_TOF) facility at the European Laboratory for Particle Physics (CERN) is a pulsed white-spectrum neutron spallation source producing neutrons for two experimental areas: the Experimental Area 1 (EAR1), located 185 m horizontall ...

2021

Laser powder-bed fusion of metallic alloys with enhanced microstructures and properties

Navid Sohrabi

Laser powder-bed fusion (LPBF) is an additive manufacturing (AM) process that uses a laser to selectively melt a powder bed. This process can build dense samples with complicated geometries from a wide variety of metallic alloys. In this thesis, LPBF of al ...

EPFL2021

Characterization of untransformed ferrite in 10Cr and 12Cr ODS steels

Roland Logé

Two new ferrito-martensitic oxide dispersion strengthened (ODS) steels reinforced with (Y, Ti, O) nanoparticles were elaborated using a high-energy attritor. The milled powder was consolidated by hot extrusion at 1050 degrees C. The two types of ODS steels ...

ELSEVIER SCI LTD2021

Page 2 sur 2