Publications associées à Concrete Fracture Process Zone Characterization with Fiber Optics

Publications associées (32)

Fluid Chemistry Effect on Localized and Ductile Deformation of a Porous Sandstone

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer, Francesco Lazari

In geological reservoirs, pore fluid chemistry can affect rock strength by inducing mineral dissolution, precipitation, and alteration, among other processes. Increasing pressure and temperature can shift deformation from localized to ductile, decreasing p ...

2025

Deciphering tensile fatigue behavior of UHPFRC using magnetoscopy, DIC and acoustic emission

Eugen Brühwiler, Alain Nussbaumer, Jian Zhan

To explore the governing mechanism underlying the tensile fatigue behavior of Ultra-high Performance Fiber Reinforced Cementitious Composites (UHPFRC), this study tested eight specimens using four advanced non-destructive measurement techniques. First, mag ...

2025

Quench Detection and Temperature Measurement With Fiber Optic Sensors

Davide Uglietti, Kamil Sedlák

For the EU DEMO conductor testing, a temperature sensor based on Fiber Bragg Grating (FBG) optical fiber is studied at the EPFL Swiss Plasma Center. The SULTAN test facility has been upgraded to use fiber optic sensor for temperature monitoring and quench ...

IEEE Institute of Electrical and Electronics Engineers2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Moulding and Microfluidic Wet Spinning of the Soft Polymer Optical Fibers for Sensory Applications

Khushdeep Sharma

Polymer optical fibre (POFs) based wearable sensors have attracted a lot of attention in the field of healthcare and biomedical applications. They are in particular envision as the next generation of sensors for the continuous, real-time n ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

High energy-density electrostatic actuators for soft robotics

Sylvain Thomas Schaller

This thesis reports high energy-density electrostatic actuators for use in soft robotics. This thesis has two main parts: a) a detailed study of electro-adhesion using microfabricated electrodes, and b) a flexi-ble fiber-shaped linear motor. Electro-adhesi ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Parametric Wavelength Conversion in Waveguiding Structures: Efficiency, Bandwidth and Polarization

Arman Ayan

Photonics integrated circuits are a promising solution for the growing demands of data transmission and future system-on-chip technologies. Within this context, nonlinear optical interactions offer unique opportunities for all-optical processing, sampling, ...

EPFL2024

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Tunable pump compression and fast modulation for pulsed THz generation

Ileana-Cristina Benea-Chelmus, Alessandro Tomasino, Yazan Lampert Almahmoud, Shima Rajabali

We demonstrate tunable dispersion compensation of femtosecond pulses at telecom wavelengths for broadband Terahertz generation in 7.5-meter fiber link using a Silicon prism pair. The prism pair enhances the amplitude of the THz E-field in InGaAs photocondu ...

IEEE2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Uniaxial Cyclic and Tensile Tests on Structural Metallic Materials

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Selimcan Ozden

Experimental data is imperative to characterize the behavior of materials used in structural analysis models. The aim of this data paper is to establish a database of material-scale uniaxial experiments, primarily conducted at EPFL, to assist with simulati ...

ASCE-AMER SOC CIVIL ENGINEERS2023

Space-time wave packets with reduced divergence and tunable group velocity generated in free space after multi-mode fiber propagation

Tobias Kippenberg, Maxim Karpov

Previously, space-time wave packets (STWPs) have been gen-erated in free space with reduced diffraction and a tunable group velocity by combining multiple frequency comb lines each carrying a single Bessel mode with a unique wave num-ber. It might be poten ...

Optica Publishing Group2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023