In situ X-ray tomography observation of inhomogeneous deformation in semi-solid aluminium alloys

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (30)

Brittle faulting of ductile rock induced by pore fluid pressure build‐up

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, François Xavier Thibault Passelègue

Under upper crustal conditions, deformations are primarily brittle (i.e., localized) and accommodated by frictional mechanisms. At greater depth, deformations are ductile (i.e., distributed) and accommodated by crystal plasticity, diffusion mass transfer o ...

2021

Discussion on "Experimental Deformation of Opalinus Clay at Elevated Temperature and Pressure Conditions: Mechanical Properties and the Influence of Rock Fabric" of Schuster, V., Rybacki, E., Bonnelye, A., Herrmann, J., Schleicher, AM, Dresen, G

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

The testing procedure and results on saturated samples of Opalinus Clay in the work of Schuster et al. (Rock Mech Rock Eng https://doi.org/10.1007/ s00603-021-02474-3, 2021) were conducted and presented using strain rates two to four orders of magnitudes h ...

2022

Coupled segregation mechanisms of Sc, Zr and Mn at theta ' interfaces enhances the strength and thermal stability of Al-Cu alloys

Baptiste Thomas Jean Rouxel, Lu Jiang

The refinement and thermal stability of intermediate theta-prime (theta') precipitates are critical in the development of new high strength 2xxx series aluminium-copper (Al-Cu) alloys for high temperature applications. In this work, we use trace additions ...

PERGAMON-ELSEVIER SCIENCE LTD2021

The mechanics of shear failures in RC slabs based on refined measurements

Raffaele Cantone

Reinforced concrete planar members, as slabs and shells, are structural elements commonly used in the construction technique, which are typically designed without the arrangement of shear reinforcement. Despite the fact that this solution allows for fast a ...

EPFL2021

{10(1)over-bar2} twinning mechanism during in situ micro-tensile loading of pure Mg: Role of basal slip and twin-twin interactions

Johann Michler, Amit Sharma, Daniele Casari, Roland Logé, Xavier Maeder, Nicolò Maria Della Ventura

An SEM in situ uniaxial tensile testing setup allowing HR-EBSD acquisition during deformation was used to study the extension twinning mechanism in magnesium(Mg) at the micron scale. Structures were fabricated with two different crystal orientations, respe ...

2021

Phase transformation induced distortions in red gold alloys

Margaux Nathalie Dominique Larcher

Red gold alloys owe their warm and attractive colour to the combination of gold and copper atoms. Thanks to their good mechanical properties and resistance to corrosion, red gold alloys are used in luxury industries as well as in dentistry. Around the equi ...

EPFL2021

Effect of Ag Addition on the Hot Deformation, Constitutive Equations and Processing Maps of a Hot Extruded Mg-Gd-Y Alloy

Roland Logé

Hot deformation behavior of the extruded Mg-6Gd-3Y (GW63) and Mg-6Gd-3Y-1Ag (GW63-1Ag) alloys was assessed by shear punch testing (SPT) method in the temperature range of 623 K to 723 K and shear strain rate of 1.6 x 10(-2)to 1.3 x 10(-1) s(-1). Microstruc ...

SPRINGER2020

High entropy alloys: A focused review of mechanical properties and deformation mechanisms

William Curtin

The high-entropy alloy (HEA) concept was based on the idea that high mixing entropy can promote formation of stable single-phase microstructures. During the past 15 years, various alloy systems have been explored to identify HEA systems with improved prope ...

PERGAMON-ELSEVIER SCIENCE LTD2020

Deformation mechanisms in a superelastic NiTi alloy: An in-situ high resolution digital image correlation study

Helena Van Swygenhoven, Efthymios Polatidis

An in-situ high resolution digital image correlation investigation during uniaxial tensile deformation reveals the recoverable and the non-recoverable strain mechanisms in a Ni51Ti49 alloy with a mean grain size of 35 mu m. Recoverable strain is due to the ...

2020

Glenoid bone strain after anatomical total shoulder arthroplasty: In vitro measurements with micro-CT and digital volume correlation

Dominique Pioletti, Alexandre Terrier, Alain Farron, Yasmine Boulanaache

Glenoid implant loosening remains a major source of failure and concern after anatomical total shoulder arthroplasty (aTSA). It is assumed to be associated with eccentric loading and excessive bone strain, but direct measurement of bone strain after aTSA i ...

2020

Page 2 sur 2