Publications associées à Quasi-static and dynamic fracture behaviour of rock materials: phenomena and mechanisms

Publications associées (31)

Deciphering tensile fatigue behavior of UHPFRC using magnetoscopy, DIC and acoustic emission

Eugen Brühwiler, Alain Nussbaumer, Jian Zhan

To explore the governing mechanism underlying the tensile fatigue behavior of Ultra-high Performance Fiber Reinforced Cementitious Composites (UHPFRC), this study tested eight specimens using four advanced non-destructive measurement techniques. First, mag ...

2025

Time-Dependent Deformation of Sandstone due to Chemical Corrosion: An Investigation Using the Heterogeneous Grain-Based Phase-Field Method

Alexandra Roma Larisa Kushnir

Fractures are diverse geological features. Despite extensive research on their varied geometries and growth mechanisms, there has been relatively little focus on how acid-rock interactions, such as reactive transport and precipitation, influence crack grow ...

SPRINGER WIEN2025

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Tensile Properties of Ex-Situ Ti-TiC Metal Matrix Composites Manufactured by Laser Powder Bed Fusion

Roland Logé

Titanium-based Metal Matrix Composites (MMCs) manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing the high reinforcement contents needed to substantially improve elastic modulus while conserving signifi ...

2024

Improved Material Formulations for Thick Adhesive Joints in Wind Turbine Blades

Jialiang Fan

Wind turbine rotor blades are usually fabricated using composite materials and epoxy adhesive to bond the elements together. Due to their large size, the thickness of the adhesive layer varies from 1 to up to 30 mm depending on the position. The failure of ...

EPFL2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Mode I fracture of thick adhesively bonded GFRP composite joints for wind turbine rotor blades

Véronique Michaud, Anastasios Vassilopoulos, Jialiang Fan

This article investigates the effects of voids, joint geometry, and test conditions on the quasi-static Mode I fracture performance of thick adhesive Double Cantilever Beam (DCB) joints such as those prevailing in wind industry and shipbuilding. The specim ...

2024

Experimental and Analytical Investigation of Deflection of R-UHPFRC Beams Subjected to Loading-Unloading

Eugen Brühwiler, Bartlomiej Wojciech Sawicki

Under service conditions, R-UHPFRC (Reinforced Ultra High Performance Fiber Reinforced Cementitious composite) beams exhibit residual deflection after loading-unloading. This is due to the tensile strain hardening behavior of UHPFRC. The precise calculatio ...

Springer2024

Formulation of stress intensity factor under pure bending condition in multilayer pavements using numerical study and model tree approach

Seyed Mahmood Hamze Ziabari

The tensile deformation of top-down cracks significantly influences pavement delamination. Accurately formulating the stress intensity factor (SIF) is crucial for assessing the stress/strain near crack tips. In the present study, a robust data mining metho ...

Wiley2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Strain-based analysis on the influence of local undercut geometry on fatigue crack initiation life

Alain Nussbaumer

The local undercut defects at the weld toe provide a potential initiation site for fatigue cracks and significantly impact the structure's fatigue strength. The influence of continuous undercut depth on fatigue performance is widely studied, but the resear ...

2024

The rise of aerial additive manufacturing in construction: a review of material advancements

Mirko Kovac, Yusuf Furkan Kaya

The construction industry has recently increased the adoption of additive manufacturing (AM, also known as 3D-printing) technologies. This review paper presents the state of the art of ground-based AM systems in construction, focusing comprehensively on de ...

2024