Publications associées à Plastic flow properties and fracture toughness characterization of unirradiated and irradiated tempered martensitic steels

Publications associées (36)

Fluid Chemistry Effect on Localized and Ductile Deformation of a Porous Sandstone

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer, Francesco Lazari

In geological reservoirs, pore fluid chemistry can affect rock strength by inducing mineral dissolution, precipitation, and alteration, among other processes. Increasing pressure and temperature can shift deformation from localized to ductile, decreasing p ...

2025

Deciphering tensile fatigue behavior of UHPFRC using magnetoscopy, DIC and acoustic emission

Eugen Brühwiler, Alain Nussbaumer, Jian Zhan

To explore the governing mechanism underlying the tensile fatigue behavior of Ultra-high Performance Fiber Reinforced Cementitious Composites (UHPFRC), this study tested eight specimens using four advanced non-destructive measurement techniques. First, mag ...

2025

Influence of the Horizontal-to-Vertical Compressive Strength of Hollow Clay Bricks on the In-Plane Drift Capacity of Unreinforced Masonry Walls

Katrin Beyer, Savvas Saloustros, Ernesto Andrés Inzunza Araya

The seismic damage of masonry walls is reflected in cracks that tend to start at the head and bed joints and subsequently propagates through the masonry units. In this regard, the horizontal-to-vertical compressive strength ratio of bricks might have the a ...

2025

Time-Dependent Deformation of Sandstone due to Chemical Corrosion: An Investigation Using the Heterogeneous Grain-Based Phase-Field Method

Alexandra Roma Larisa Kushnir

Fractures are diverse geological features. Despite extensive research on their varied geometries and growth mechanisms, there has been relatively little focus on how acid-rock interactions, such as reactive transport and precipitation, influence crack grow ...

SPRINGER WIEN2025

Achieving strength-ductility synergy in AISI 904L superaustenitic alloy through severe plastic deformation and post-deformation annealing

Mohammad Mobasheri

The evolution of microstructure and mechanical properties of AISI 904L stainless steel subjected to high-pressure torsion (HPT) and post-deformation annealing was investigated. A nanocrystalline microstructure with an average grain size of 48 nm was obtain ...

2025

Improved Material Formulations for Thick Adhesive Joints in Wind Turbine Blades

Jialiang Fan

Wind turbine rotor blades are usually fabricated using composite materials and epoxy adhesive to bond the elements together. Due to their large size, the thickness of the adhesive layer varies from 1 to up to 30 mm depending on the position. The failure of ...

EPFL2024

Tensile Properties of Ex-Situ Ti-TiC Metal Matrix Composites Manufactured by Laser Powder Bed Fusion

Roland Logé

Titanium-based Metal Matrix Composites (MMCs) manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing the high reinforcement contents needed to substantially improve elastic modulus while conserving signifi ...

2024

Refractive Index Matched (RIM) PIV in Free Surface Flows of Particle-Laden Yield Stress Fluids

Christophe Ancey, Yanan Chen

Flow of lava, avalanches, mudslides, and many geophysical and planetary flow systems are examples of free-surface flows of Yield Stress Fluids (YSFs). This category of fluids is known for its dual behavior below- and above a yielding threshold for the appl ...

2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

Gamma noise to non-invasively monitor nuclear research reactors

Andreas Pautz, Vincent Pierre Lamirand, Oskari Ville Pakari, Pavel Frajtag, Tom Mager

Autonomous nuclear reactor monitoring is a key aspect of the International Atomic Energy Agency’s strategy to ensure nonproliferation treaty compliance. From the rise of small modular reactor technology, decentralized nuclear reactor fleets may strain the ...

Nature Research2024

A low-temperature prismatic slip instability in Mg understood using machine learning potentials

William Curtin, Xin Liu, Binglun Yin

Prismatic slip in magnesium at temperatures T

PERGAMON-ELSEVIER SCIENCE LTD2023

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Crack tip kinematics reveal the process zone structure in brittle fracture

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

When brittle hydrogels fail, several mechanisms conspire to alter the state of stress near the tip of a crack, and it is challenging to identify which mechanism is dominant. In the fracture of brittle solids, a sufficient far-field stress results in the co ...

PERGAMON-ELSEVIER SCIENCE LTD2023

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023