Manufacturing and Preliminary Performance Expectations of Nb3Sn Based Conductors Allocated for the First ITER TF Coil With CICC From Korea

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (31)

Tritium removal from JET-ILW after T and D-T experimental campaigns

Henri Weisen, Mikhail Maslov

After the second Deuterium-Tritium Campaign (DTE2) in the JET tokamak with the ITER-Like Wall (ILW) and full tritium campaigns that preceded and followed after the DTE2, a sequence of fuel recovery methods was applied to promote tritium removal from wall c ...

IOP Publishing Ltd2023

Full-discharge simulation and optimization with the RAPTOR code, from present tokamaks to ITER and DEMO

Simon Van Mulders

Tokamak devices aim to magnetically confine a hydrogen plasma at sufficiently high pressure to achieve net energy production from nuclear fusion of light isotopes. Predictive modeling and optimization is crucial for reliable operation of tokamak reactors, ...

EPFL2023

The MAgnet Design Explorer algorithm (MADE) for LTS, Hybrid or HTS toroidal and poloidal systems of a tokamak with a view to DEMO

The European Roadmap to Fusion Electricity (Federici et al., 2018) [1] details the path to complete within the next three decades the DEMOnstration power plant, DEMO, aiming to a net gain of Energy Q=40. The 2018 DEMO baseline considers a 2 GW tokamak devi ...

2023

ICRH assisted breakdown study on JET

Thomas Binderup Jensen, Benoît Labit, Haomin Sun

Ion cyclotron (IC) wave assisted breakdown has the potential to increase the robustness of plasma initiation during the ITER pre-fusion operation phase. Studies were performed at JET at ITER relevant loop electric field, E-loop ? 0.33 Vm(-1), and a range o ...

IOP Publishing Ltd2023

High power mm-wave loss measurements of ITER ex-vessel waveguide components at the FALCON test facility at the Swiss Plasma Center

René Chavan, Timothy Goodman, Avelino Mas Sanchez, Anastasia Xydou, Humberto Torreblanca Quiroz

Many future fusion devices will rely heavily, if not solely, on electron cyclotron (EC) heating subsystems to provide bulk heating, instability control (neoclassical tearing mode (NTM) stabilization), and thermal instability control. Efficient use of the i ...

E D P SCIENCES2023

EMC and earthing concept of the ITER EC-system

Damien Fasel, Ugo Siravo, Francisco Sanchez, Jérémie Dubray

Gyrotrons and High Voltage Power Supplies (HVPS) used on electron cyclotron (EC) systems are the source of large electromagnetic interference (EMI). Arcing events inside gyrotrons is the most frequently cited issue, but fast shutdown of a HVPS can produce ...

2023

A new 3MW ECRH system at 105 GHz for WEST*

Stefano Alberti, Timothy Goodman, Jean-Philippe Hogge, Ioannis Pagonakis, Konstantinos Avramidis

The aim of the WEST experiments is to master long plasma pulses (1000s) and expose ITER-like tungsten wall to deposited heat fluxes up to 10 MW/m2. To increase the margin to reach the H-Mode and to control W-impurities in the plasma, the installation of an ...

2023

Essay: Overcoming the Obstacles to a Magnetic Fusion Power Plant

Ambrogio Fasoli

Fusion occurs when light nuclei combine to form heavier nuclei. The energy released in this process powers the stars and can provide humankind with a safe, sustainable, and clean source of baseload electricity, a valuable tool in the fight against climate ...

AMER PHYSICAL SOC2023

Present design of the Steering Mirror Assembly (SMA) for ITER ECHUL

René Chavan, Timothy Goodman, Anastasia Xydou

In the ITER Tokamak, four Electron Cyclotron Heating Upper Launchers (ECHUL) are needed to control plasma instabilities at the rational surfaces, most importantly the q = 3/2 and q = 2/1 neoclassical tearing modes (NTMs). Each ECHUL is equipped with a set ...

2023

Studies on EU-DEMO 3D coils requirements and conceptual design for error field correction and plasma control

Pierluigi Bruzzone, Hartmut Zohm, Leonardo Pigatto

This work presents the initial studies on the requirements for the design of 3D coils on EU-DEMO. The use of 3D coils in present machines includes two main purposes: the first one is the Error Field Correction (EFC). The EFC aims at minimizing the intrinsi ...

Elsevier Science Sa2023

3D Characterisation of Turbulent Plasma Filaments Using Gas Puff Imaging in the Tokamak à Configuration Variable

Nicola Offeddu

A key challenge for the development of fusion reactors based on magnetic confinement, such as tokamaks and stellarators, is the control of the turbulent processes. The most prominent feature of turbulence in the Scrape-Off Layer (SOL), the volume between t ...

EPFL2023

Page 2 sur 2