Publications associées à Review of dynamic testing methods and results of rock materials in tension

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Corentin Jean-Marie Rémi Noël

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Propagation of planar three-dimensional buoyant hydraulic fractures

Andreas Möri

Hydraulic fractures are driven by an internal fluid pressure exceeding the minimum compressive stress, propagating in a direction perpendicular to the latter. This class of tensile fractures has gained interest over the last fifty years due to the developm ...

EPFL2023

Bounding the localized to ductile transition in porous rocks: implications for geo-reservoirs

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer

Porous rocks have long been the focus of intense research driven by their importance in our society as host to our most essential resources (oil, gas, water, geothermal energy, etc), yet their rheology remains poorly understood. With increasing depth, poro ...

2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Cyril Cayron, Roland Logé, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Elongated hydraulic fracture emerging from layers of alternating fracture toughness

Brice Tanguy Alphonse Lecampion, Carlo Peruzzo

Whether used to enhance the hydrocarbon production from low permeability rocks or to measure the minimum in-situ principal stress in rock formations, height growth of a hydraulic fracture above the formation of interest is a key metric for the design of su ...

2023

Thermophysical and thermomechanical properties of basalt-phenolic FRP rebars under high temperature

Thomas Keller, Hongwei Zhu, Ting Li, Jiahui Shen

An experimental investigation was conducted on the thermophysical and thermomechanical properties of phenolic-basalt fiber-reinforced polymer (P-BFRP) rebars subjected to high temperature. As a comparison, vinylBFRP (V-BFRP) and epoxy-BFRP (E-BFRP) rebars ...

ELSEVIER SCI LTD2022

Strained crystalline nanomechanical resonators with quality factors above 10 billion

Tobias Kippenberg, Sergey Fedorov, Nils Johan Engelsen, Alberto Beccari

In strained mechanical resonators, the concurrence of tensile stress and geometric nonlinearity dramatically reduces dissipation. This phenomenon, called dissipation dilution, is employed in mirror suspensions of gravitational-wave interferometers and at t ...

NATURE PORTFOLIO2022

Strong silicon oxide inclusions in iron

Andreas Mortensen, Léa Deillon, Alejandra Inés Slagter, Joris Pierre Everaerts

Oxide inclusions are ubiquitous in steel and are known to affect, generally in a negative sense, the mechanical performance of steel products. Micromechanical properties of those phases are therefore important, yet they have remained largely unexplored. We ...

2022

Weakening effect of various pore fluids on the tensile strength of granite

Guanyi Lu

Laboratory three-point bending experiments are carried out to evaluate the effect of various fluids on the tensile strength of granite. The granite specimens were tested under both dry and saturated conditions. The fluids used to saturate the granite inclu ...

SPRINGER HEIDELBERG2022

Prediction of crack nucleation and propagation in porous ceramics using the phase-field approach

Arata Nakajo

The relevance of the phase-field approach to simulate the fracture in porous ceramics has been investigated. For this purpose, the conditions for the crack initiation using the phase-field model have been compared to the theoretical predictions of the coup ...

ELSEVIER2022

Strengthening mechanisms in dilute and random solid solution high-entropy BCC alloys

Alireza Ghafarollahi

Tuning the mechanical properties of metals, including strength, through adjusting the type and/or concentration of added solute elements, has been recognized as an effective way to design and produce materials with desired or optimized mechanical propertie ...

EPFL2022

Sustainable polyesters via direct functionalization of lignocellulosic sugars

Yves Leterrier, Véronique Michaud, François Maréchal, Jeremy Luterbacher, Harm-Anton Klok, Graham Reid Dick, Adrien Julien Demongeot, Christèle Rayroud, Maxime Alexandre Clément Hedou, Thibault Rambert

The development of sustainable plastics from abundant renewable feedstocks has been limited by the complexity and efficiency of their production, as well as their lack of competitive material properties. Here we demonstrate the direct transformation of the ...

2022

Understanding the mechanisms of adhesive wear for heterogeneous materials through atomistic simulations

Jean-François Molinari, Sacha Zenon Wattel, Antonio Joaquin Garcia Suarez

When two rough surfaces slide against each other, two main behaviors can be observed at the asperity level: A ductile behavior where the asperities tend to smooth out or a brittle behavior where the asperities detach and form debris. Recently, a critical l ...

2022

Deformation and Fracture of Tough Microstructured Hydrogels

Michael David Kessler

Many natural materials are structured on different length scales. This structuring often leads to an intricate interplay between soft and stiff components, which significantly improves the fracture toughness of these materials. A class of soft material tha ...

EPFL2022